Audio: 8916 Audio HAL bringup changes
-Separate platform specific code from generic audio HAL code
-Platform specific code is:
- platform initialization
- pcm device selection
- pcm stream configuration
- sound device selection
- acdb ID selection
- HDMI configuration
Change-Id: I9b02d60035ea632776e59c9d953909d3b851f3d7
diff --git a/hal/msm8916/platform.h b/hal/msm8916/platform.h
new file mode 100644
index 0000000..9b97648
--- /dev/null
+++ b/hal/msm8916/platform.h
@@ -0,0 +1,118 @@
+/*
+ * Copyright (C) 2013 The Android Open Source Project
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef QCOM_AUDIO_PLATFORM_H
+#define QCOM_AUDIO_PLATFORM_H
+
+/*
+ * Below are the devices for which is back end is same, SLIMBUS_0_RX.
+ * All these devices are handled by the internal HW codec. We can
+ * enable any one of these devices at any time
+ */
+#define AUDIO_DEVICE_OUT_ALL_CODEC_BACKEND \
+ (AUDIO_DEVICE_OUT_EARPIECE | AUDIO_DEVICE_OUT_SPEAKER | \
+ AUDIO_DEVICE_OUT_WIRED_HEADSET | AUDIO_DEVICE_OUT_WIRED_HEADPHONE)
+
+/* Sound devices specific to the platform
+ * The DEVICE_OUT_* and DEVICE_IN_* should be mapped to these sound
+ * devices to enable corresponding mixer paths
+ */
+enum {
+ SND_DEVICE_NONE = 0,
+
+ /* Playback devices */
+ SND_DEVICE_MIN,
+ SND_DEVICE_OUT_BEGIN = SND_DEVICE_MIN,
+ SND_DEVICE_OUT_HANDSET = SND_DEVICE_OUT_BEGIN,
+ SND_DEVICE_OUT_SPEAKER,
+ SND_DEVICE_OUT_SPEAKER_REVERSE,
+ SND_DEVICE_OUT_HEADPHONES,
+ SND_DEVICE_OUT_SPEAKER_AND_HEADPHONES,
+ SND_DEVICE_OUT_VOICE_HANDSET,
+ SND_DEVICE_OUT_VOICE_SPEAKER,
+ SND_DEVICE_OUT_VOICE_HEADPHONES,
+ SND_DEVICE_OUT_HDMI,
+ SND_DEVICE_OUT_SPEAKER_AND_HDMI,
+ SND_DEVICE_OUT_BT_SCO,
+ SND_DEVICE_OUT_VOICE_HANDSET_TMUS,
+ SND_DEVICE_OUT_VOICE_TTY_FULL_HEADPHONES,
+ SND_DEVICE_OUT_VOICE_TTY_VCO_HEADPHONES,
+ SND_DEVICE_OUT_VOICE_TTY_HCO_HANDSET,
+ SND_DEVICE_OUT_END,
+
+ /*
+ * Note: IN_BEGIN should be same as OUT_END because total number of devices
+ * SND_DEVICES_MAX should not exceed MAX_RX + MAX_TX devices.
+ */
+ /* Capture devices */
+ SND_DEVICE_IN_BEGIN = SND_DEVICE_OUT_END,
+ SND_DEVICE_IN_HANDSET_MIC = SND_DEVICE_IN_BEGIN,
+ SND_DEVICE_IN_SPEAKER_MIC,
+ SND_DEVICE_IN_HEADSET_MIC,
+ SND_DEVICE_IN_HANDSET_MIC_AEC,
+ SND_DEVICE_IN_SPEAKER_MIC_AEC,
+ SND_DEVICE_IN_HEADSET_MIC_AEC,
+ SND_DEVICE_IN_VOICE_SPEAKER_MIC,
+ SND_DEVICE_IN_VOICE_HEADSET_MIC,
+ SND_DEVICE_IN_HDMI_MIC,
+ SND_DEVICE_IN_BT_SCO_MIC,
+ SND_DEVICE_IN_CAMCORDER_MIC,
+ SND_DEVICE_IN_VOICE_DMIC_EF,
+ SND_DEVICE_IN_VOICE_DMIC_BS,
+ SND_DEVICE_IN_VOICE_DMIC_EF_TMUS,
+ SND_DEVICE_IN_VOICE_SPEAKER_DMIC_EF,
+ SND_DEVICE_IN_VOICE_SPEAKER_DMIC_BS,
+ SND_DEVICE_IN_VOICE_TTY_FULL_HEADSET_MIC,
+ SND_DEVICE_IN_VOICE_TTY_VCO_HANDSET_MIC,
+ SND_DEVICE_IN_VOICE_TTY_HCO_HEADSET_MIC,
+ SND_DEVICE_IN_VOICE_REC_MIC,
+ SND_DEVICE_IN_VOICE_REC_DMIC_EF,
+ SND_DEVICE_IN_VOICE_REC_DMIC_BS,
+ SND_DEVICE_IN_VOICE_REC_DMIC_EF_FLUENCE,
+ SND_DEVICE_IN_VOICE_REC_DMIC_BS_FLUENCE,
+ SND_DEVICE_IN_END,
+
+ SND_DEVICE_MAX = SND_DEVICE_IN_END,
+
+};
+
+#define MIXER_CARD 0
+#define SOUND_CARD 0
+
+#define DEFAULT_OUTPUT_SAMPLING_RATE 48000
+
+/*
+ * tinyAlsa library interprets period size as number of frames
+ * one frame = channel_count * sizeof (pcm sample)
+ * so if format = 16-bit PCM and channels = Stereo, frame size = 2 ch * 2 = 4 bytes
+ * DEEP_BUFFER_OUTPUT_PERIOD_SIZE = 1024 means 1024 * 4 = 4096 bytes
+ * We should take care of returning proper size when AudioFlinger queries for
+ * the buffer size of an input/output stream
+ */
+#define DEEP_BUFFER_OUTPUT_PERIOD_SIZE 1024
+#define DEEP_BUFFER_OUTPUT_PERIOD_COUNT 8
+#define LOW_LATENCY_OUTPUT_PERIOD_SIZE 256
+#define LOW_LATENCY_OUTPUT_PERIOD_COUNT 2
+
+#define HDMI_MULTI_PERIOD_SIZE 336
+#define HDMI_MULTI_PERIOD_COUNT 8
+#define HDMI_MULTI_DEFAULT_CHANNEL_COUNT 6
+#define HDMI_MULTI_PERIOD_BYTES (HDMI_MULTI_PERIOD_SIZE * HDMI_MULTI_DEFAULT_CHANNEL_COUNT * 2)
+
+#define AUDIO_CAPTURE_PERIOD_SIZE 512
+#define AUDIO_CAPTURE_PERIOD_COUNT 16
+
+#endif // QCOM_AUDIO_PLATFORM_H