| /*- |
| * Largely written by Julian Elischer (julian@tfs.com) |
| * for TRW Financial Systems. |
| * |
| * TRW Financial Systems, in accordance with their agreement with Carnegie |
| * Mellon University, makes this software available to CMU to distribute |
| * or use in any manner that they see fit as long as this message is kept with |
| * the software. For this reason TFS also grants any other persons or |
| * organisations permission to use or modify this software. |
| * |
| * TFS supplies this software to be publicly redistributed |
| * on the understanding that TFS is not responsible for the correct |
| * functioning of this software in any circumstances. |
| * |
| * Ported to run under 386BSD by Julian Elischer (julian@tfs.com) Sept 1992 |
| * |
| * $FreeBSD$ |
| */ |
| |
| /* |
| * SCSI general interface description |
| */ |
| |
| #ifndef _SCSI_SCSI_ALL_H |
| #define _SCSI_SCSI_ALL_H 1 |
| |
| #include <sys/cdefs.h> |
| |
| #ifdef _KERNEL |
| /* |
| * This is the number of seconds we wait for devices to settle after a SCSI |
| * bus reset. |
| */ |
| extern int scsi_delay; |
| #endif /* _KERNEL */ |
| |
| /* |
| * SCSI command format |
| */ |
| |
| /* |
| * Define dome bits that are in ALL (or a lot of) scsi commands |
| */ |
| #define SCSI_CTL_LINK 0x01 |
| #define SCSI_CTL_FLAG 0x02 |
| #define SCSI_CTL_VENDOR 0xC0 |
| #define SCSI_CMD_LUN 0xA0 /* these two should not be needed */ |
| #define SCSI_CMD_LUN_SHIFT 5 /* LUN in the cmd is no longer SCSI */ |
| |
| #define SCSI_MAX_CDBLEN 16 /* |
| * 16 byte commands are in the |
| * SCSI-3 spec |
| */ |
| #if defined(CAM_MAX_CDBLEN) && (CAM_MAX_CDBLEN < SCSI_MAX_CDBLEN) |
| #error "CAM_MAX_CDBLEN cannot be less than SCSI_MAX_CDBLEN" |
| #endif |
| |
| /* 6byte CDBs special case 0 length to be 256 */ |
| #define SCSI_CDB6_LEN(len) ((len) == 0 ? 256 : len) |
| |
| /* |
| * This type defines actions to be taken when a particular sense code is |
| * received. Right now, these flags are only defined to take up 16 bits, |
| * but can be expanded in the future if necessary. |
| */ |
| typedef enum { |
| SS_NOP = 0x000000, /* Do nothing */ |
| SS_RETRY = 0x010000, /* Retry the command */ |
| SS_FAIL = 0x020000, /* Bail out */ |
| SS_START = 0x030000, /* Send a Start Unit command to the device, |
| * then retry the original command. |
| */ |
| SS_TUR = 0x040000, /* Send a Test Unit Ready command to the |
| * device, then retry the original command. |
| */ |
| SS_MASK = 0xff0000 |
| } scsi_sense_action; |
| |
| typedef enum { |
| SSQ_NONE = 0x0000, |
| SSQ_DECREMENT_COUNT = 0x0100, /* Decrement the retry count */ |
| SSQ_MANY = 0x0200, /* send lots of recovery commands */ |
| SSQ_RANGE = 0x0400, /* |
| * This table entry represents the |
| * end of a range of ASCQs that |
| * have identical error actions |
| * and text. |
| */ |
| SSQ_PRINT_SENSE = 0x0800, |
| SSQ_UA = 0x1000, /* Broadcast UA. */ |
| SSQ_RESCAN = 0x2000, /* Rescan target for LUNs. */ |
| SSQ_LOST = 0x4000, /* Destroy the LUNs. */ |
| SSQ_MASK = 0xff00 |
| } scsi_sense_action_qualifier; |
| |
| /* Mask for error status values */ |
| #define SS_ERRMASK 0xff |
| |
| /* The default, retyable, error action */ |
| #define SS_RDEF SS_RETRY|SSQ_DECREMENT_COUNT|SSQ_PRINT_SENSE|EIO |
| |
| /* The retyable, error action, with table specified error code */ |
| #define SS_RET SS_RETRY|SSQ_DECREMENT_COUNT|SSQ_PRINT_SENSE |
| |
| /* Wait for transient error status to change */ |
| #define SS_WAIT SS_TUR|SSQ_MANY|SSQ_DECREMENT_COUNT|SSQ_PRINT_SENSE |
| |
| /* Fatal error action, with table specified error code */ |
| #define SS_FATAL SS_FAIL|SSQ_PRINT_SENSE |
| |
| struct scsi_generic |
| { |
| u_int8_t opcode; |
| u_int8_t bytes[11]; |
| }; |
| |
| struct scsi_request_sense |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| #define SRS_DESC 0x01 |
| u_int8_t unused[2]; |
| u_int8_t length; |
| u_int8_t control; |
| }; |
| |
| struct scsi_test_unit_ready |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| u_int8_t unused[3]; |
| u_int8_t control; |
| }; |
| |
| struct scsi_receive_diag { |
| uint8_t opcode; |
| uint8_t byte2; |
| #define SRD_PCV 0x01 |
| uint8_t page_code; |
| uint8_t length[2]; |
| uint8_t control; |
| }; |
| |
| struct scsi_send_diag { |
| uint8_t opcode; |
| uint8_t byte2; |
| #define SSD_UNITOFFL 0x01 |
| #define SSD_DEVOFFL 0x02 |
| #define SSD_SELFTEST 0x04 |
| #define SSD_PF 0x10 |
| #define SSD_SELF_TEST_CODE_MASK 0xE0 |
| #define SSD_SELF_TEST_CODE_SHIFT 5 |
| #define SSD_SELF_TEST_CODE_NONE 0x00 |
| #define SSD_SELF_TEST_CODE_BG_SHORT 0x01 |
| #define SSD_SELF_TEST_CODE_BG_EXTENDED 0x02 |
| #define SSD_SELF_TEST_CODE_BG_ABORT 0x04 |
| #define SSD_SELF_TEST_CODE_FG_SHORT 0x05 |
| #define SSD_SELF_TEST_CODE_FG_EXTENDED 0x06 |
| uint8_t reserved; |
| uint8_t length[2]; |
| uint8_t control; |
| }; |
| |
| struct scsi_sense |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| u_int8_t unused[2]; |
| u_int8_t length; |
| u_int8_t control; |
| }; |
| |
| struct scsi_inquiry |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| #define SI_EVPD 0x01 |
| #define SI_CMDDT 0x02 |
| u_int8_t page_code; |
| u_int8_t length[2]; |
| u_int8_t control; |
| }; |
| |
| struct scsi_mode_sense_6 |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| #define SMS_DBD 0x08 |
| u_int8_t page; |
| #define SMS_PAGE_CODE 0x3F |
| #define SMS_VENDOR_SPECIFIC_PAGE 0x00 |
| #define SMS_DISCONNECT_RECONNECT_PAGE 0x02 |
| #define SMS_FORMAT_DEVICE_PAGE 0x03 |
| #define SMS_GEOMETRY_PAGE 0x04 |
| #define SMS_CACHE_PAGE 0x08 |
| #define SMS_PERIPHERAL_DEVICE_PAGE 0x09 |
| #define SMS_CONTROL_MODE_PAGE 0x0A |
| #define SMS_PROTO_SPECIFIC_PAGE 0x19 |
| #define SMS_INFO_EXCEPTIONS_PAGE 0x1C |
| #define SMS_ALL_PAGES_PAGE 0x3F |
| #define SMS_PAGE_CTRL_MASK 0xC0 |
| #define SMS_PAGE_CTRL_CURRENT 0x00 |
| #define SMS_PAGE_CTRL_CHANGEABLE 0x40 |
| #define SMS_PAGE_CTRL_DEFAULT 0x80 |
| #define SMS_PAGE_CTRL_SAVED 0xC0 |
| u_int8_t subpage; |
| #define SMS_SUBPAGE_PAGE_0 0x00 |
| #define SMS_SUBPAGE_ALL 0xff |
| u_int8_t length; |
| u_int8_t control; |
| }; |
| |
| struct scsi_mode_sense_10 |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; /* same bits as small version */ |
| #define SMS10_LLBAA 0x10 |
| u_int8_t page; /* same bits as small version */ |
| u_int8_t subpage; |
| u_int8_t unused[3]; |
| u_int8_t length[2]; |
| u_int8_t control; |
| }; |
| |
| struct scsi_mode_select_6 |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| #define SMS_SP 0x01 |
| #define SMS_PF 0x10 |
| u_int8_t unused[2]; |
| u_int8_t length; |
| u_int8_t control; |
| }; |
| |
| struct scsi_mode_select_10 |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; /* same bits as small version */ |
| u_int8_t unused[5]; |
| u_int8_t length[2]; |
| u_int8_t control; |
| }; |
| |
| /* |
| * When sending a mode select to a tape drive, the medium type must be 0. |
| */ |
| struct scsi_mode_hdr_6 |
| { |
| u_int8_t datalen; |
| u_int8_t medium_type; |
| u_int8_t dev_specific; |
| u_int8_t block_descr_len; |
| }; |
| |
| struct scsi_mode_hdr_10 |
| { |
| u_int8_t datalen[2]; |
| u_int8_t medium_type; |
| u_int8_t dev_specific; |
| u_int8_t reserved[2]; |
| u_int8_t block_descr_len[2]; |
| }; |
| |
| struct scsi_mode_block_descr |
| { |
| u_int8_t density_code; |
| u_int8_t num_blocks[3]; |
| u_int8_t reserved; |
| u_int8_t block_len[3]; |
| }; |
| |
| struct scsi_per_res_in |
| { |
| u_int8_t opcode; |
| u_int8_t action; |
| #define SPRI_RK 0x00 |
| #define SPRI_RR 0x01 |
| #define SPRI_RC 0x02 |
| #define SPRI_RS 0x03 |
| u_int8_t reserved[5]; |
| u_int8_t length[2]; |
| #define SPRI_MAX_LEN 0xffff |
| u_int8_t control; |
| }; |
| |
| struct scsi_per_res_in_header |
| { |
| u_int8_t generation[4]; |
| u_int8_t length[4]; |
| }; |
| |
| struct scsi_per_res_key |
| { |
| u_int8_t key[8]; |
| }; |
| |
| struct scsi_per_res_in_keys |
| { |
| struct scsi_per_res_in_header header; |
| struct scsi_per_res_key keys[0]; |
| }; |
| |
| struct scsi_per_res_cap |
| { |
| uint8_t length[2]; |
| uint8_t flags1; |
| #define SPRI_RLR_C 0x80 |
| #define SPRI_CRH 0x10 |
| #define SPRI_SIP_C 0x08 |
| #define SPRI_ATP_C 0x04 |
| #define SPRI_PTPL_C 0x01 |
| uint8_t flags2; |
| #define SPRI_TMV 0x80 |
| #define SPRI_ALLOW_CMD_MASK 0x70 |
| #define SPRI_ALLOW_CMD_SHIFT 4 |
| #define SPRI_ALLOW_NA 0x00 |
| #define SPRI_ALLOW_1 0x10 |
| #define SPRI_ALLOW_2 0x20 |
| #define SPRI_ALLOW_3 0x30 |
| #define SPRI_ALLOW_4 0x40 |
| #define SPRI_ALLOW_5 0x50 |
| #define SPRI_PTPL_A 0x01 |
| uint8_t type_mask[2]; |
| #define SPRI_TM_WR_EX_AR 0x8000 |
| #define SPRI_TM_EX_AC_RO 0x4000 |
| #define SPRI_TM_WR_EX_RO 0x2000 |
| #define SPRI_TM_EX_AC 0x0800 |
| #define SPRI_TM_WR_EX 0x0200 |
| #define SPRI_TM_EX_AC_AR 0x0001 |
| uint8_t reserved[2]; |
| }; |
| |
| struct scsi_per_res_in_rsrv_data |
| { |
| uint8_t reservation[8]; |
| uint8_t scope_addr[4]; |
| uint8_t reserved; |
| uint8_t scopetype; |
| #define SPRT_WE 0x01 |
| #define SPRT_EA 0x03 |
| #define SPRT_WERO 0x05 |
| #define SPRT_EARO 0x06 |
| #define SPRT_WEAR 0x07 |
| #define SPRT_EAAR 0x08 |
| uint8_t extent_length[2]; |
| }; |
| |
| struct scsi_per_res_in_rsrv |
| { |
| struct scsi_per_res_in_header header; |
| struct scsi_per_res_in_rsrv_data data; |
| }; |
| |
| struct scsi_per_res_in_full_desc |
| { |
| struct scsi_per_res_key res_key; |
| uint8_t reserved1[4]; |
| uint8_t flags; |
| #define SPRI_FULL_ALL_TG_PT 0x02 |
| #define SPRI_FULL_R_HOLDER 0x01 |
| uint8_t scopetype; |
| uint8_t reserved2[4]; |
| uint8_t rel_trgt_port_id[2]; |
| uint8_t additional_length[4]; |
| uint8_t transport_id[]; |
| }; |
| |
| struct scsi_per_res_in_full |
| { |
| struct scsi_per_res_in_header header; |
| struct scsi_per_res_in_full_desc desc[]; |
| }; |
| |
| struct scsi_per_res_out |
| { |
| u_int8_t opcode; |
| u_int8_t action; |
| #define SPRO_REGISTER 0x00 |
| #define SPRO_RESERVE 0x01 |
| #define SPRO_RELEASE 0x02 |
| #define SPRO_CLEAR 0x03 |
| #define SPRO_PREEMPT 0x04 |
| #define SPRO_PRE_ABO 0x05 |
| #define SPRO_REG_IGNO 0x06 |
| #define SPRO_REG_MOVE 0x07 |
| #define SPRO_REPL_LOST_RES 0x08 |
| #define SPRO_ACTION_MASK 0x1f |
| u_int8_t scope_type; |
| #define SPR_SCOPE_MASK 0xf0 |
| #define SPR_SCOPE_SHIFT 4 |
| #define SPR_LU_SCOPE 0x00 |
| #define SPR_EXTENT_SCOPE 0x10 |
| #define SPR_ELEMENT_SCOPE 0x20 |
| #define SPR_TYPE_MASK 0x0f |
| #define SPR_TYPE_RD_SHARED 0x00 |
| #define SPR_TYPE_WR_EX 0x01 |
| #define SPR_TYPE_RD_EX 0x02 |
| #define SPR_TYPE_EX_AC 0x03 |
| #define SPR_TYPE_SHARED 0x04 |
| #define SPR_TYPE_WR_EX_RO 0x05 |
| #define SPR_TYPE_EX_AC_RO 0x06 |
| #define SPR_TYPE_WR_EX_AR 0x07 |
| #define SPR_TYPE_EX_AC_AR 0x08 |
| u_int8_t reserved[2]; |
| u_int8_t length[4]; |
| u_int8_t control; |
| }; |
| |
| struct scsi_per_res_out_parms |
| { |
| struct scsi_per_res_key res_key; |
| u_int8_t serv_act_res_key[8]; |
| u_int8_t scope_spec_address[4]; |
| u_int8_t flags; |
| #define SPR_SPEC_I_PT 0x08 |
| #define SPR_ALL_TG_PT 0x04 |
| #define SPR_APTPL 0x01 |
| u_int8_t reserved1; |
| u_int8_t extent_length[2]; |
| u_int8_t transport_id_list[]; |
| }; |
| |
| struct scsi_per_res_out_trans_ids { |
| u_int8_t additional_length[4]; |
| u_int8_t transport_ids[]; |
| }; |
| |
| /* |
| * Used with REGISTER AND MOVE serivce action of the PERSISTENT RESERVE OUT |
| * command. |
| */ |
| struct scsi_per_res_reg_move |
| { |
| struct scsi_per_res_key res_key; |
| u_int8_t serv_act_res_key[8]; |
| u_int8_t reserved; |
| u_int8_t flags; |
| #define SPR_REG_MOVE_UNREG 0x02 |
| #define SPR_REG_MOVE_APTPL 0x01 |
| u_int8_t rel_trgt_port_id[2]; |
| u_int8_t transport_id_length[4]; |
| u_int8_t transport_id[]; |
| }; |
| |
| struct scsi_transportid_header |
| { |
| uint8_t format_protocol; |
| #define SCSI_TRN_FORMAT_MASK 0xc0 |
| #define SCSI_TRN_FORMAT_SHIFT 6 |
| #define SCSI_TRN_PROTO_MASK 0x0f |
| }; |
| |
| struct scsi_transportid_fcp |
| { |
| uint8_t format_protocol; |
| #define SCSI_TRN_FCP_FORMAT_DEFAULT 0x00 |
| uint8_t reserved1[7]; |
| uint8_t n_port_name[8]; |
| uint8_t reserved2[8]; |
| }; |
| |
| struct scsi_transportid_spi |
| { |
| uint8_t format_protocol; |
| #define SCSI_TRN_SPI_FORMAT_DEFAULT 0x00 |
| uint8_t reserved1; |
| uint8_t scsi_addr[2]; |
| uint8_t obsolete[2]; |
| uint8_t rel_trgt_port_id[2]; |
| uint8_t reserved2[16]; |
| }; |
| |
| struct scsi_transportid_1394 |
| { |
| uint8_t format_protocol; |
| #define SCSI_TRN_1394_FORMAT_DEFAULT 0x00 |
| uint8_t reserved1[7]; |
| uint8_t eui64[8]; |
| uint8_t reserved2[8]; |
| }; |
| |
| struct scsi_transportid_rdma |
| { |
| uint8_t format_protocol; |
| #define SCSI_TRN_RDMA_FORMAT_DEFAULT 0x00 |
| uint8_t reserved[7]; |
| #define SCSI_TRN_RDMA_PORT_LEN 16 |
| uint8_t initiator_port_id[SCSI_TRN_RDMA_PORT_LEN]; |
| }; |
| |
| struct scsi_transportid_iscsi_device |
| { |
| uint8_t format_protocol; |
| #define SCSI_TRN_ISCSI_FORMAT_DEVICE 0x00 |
| uint8_t reserved; |
| uint8_t additional_length[2]; |
| uint8_t iscsi_name[]; |
| }; |
| |
| struct scsi_transportid_iscsi_port |
| { |
| uint8_t format_protocol; |
| #define SCSI_TRN_ISCSI_FORMAT_PORT 0x40 |
| uint8_t reserved; |
| uint8_t additional_length[2]; |
| uint8_t iscsi_name[]; |
| /* |
| * Followed by a separator and iSCSI initiator session ID |
| */ |
| }; |
| |
| struct scsi_transportid_sas |
| { |
| uint8_t format_protocol; |
| #define SCSI_TRN_SAS_FORMAT_DEFAULT 0x00 |
| uint8_t reserved1[3]; |
| uint8_t sas_address[8]; |
| uint8_t reserved2[12]; |
| }; |
| |
| struct scsi_sop_routing_id_norm { |
| uint8_t bus; |
| uint8_t devfunc; |
| #define SCSI_TRN_SOP_BUS_MAX 0xff |
| #define SCSI_TRN_SOP_DEV_MAX 0x1f |
| #define SCSI_TRN_SOP_DEV_MASK 0xf8 |
| #define SCSI_TRN_SOP_DEV_SHIFT 3 |
| #define SCSI_TRN_SOP_FUNC_NORM_MASK 0x07 |
| #define SCSI_TRN_SOP_FUNC_NORM_MAX 0x07 |
| }; |
| |
| struct scsi_sop_routing_id_alt { |
| uint8_t bus; |
| uint8_t function; |
| #define SCSI_TRN_SOP_FUNC_ALT_MAX 0xff |
| }; |
| |
| struct scsi_transportid_sop |
| { |
| uint8_t format_protocol; |
| #define SCSI_TRN_SOP_FORMAT_DEFAULT 0x00 |
| uint8_t reserved1; |
| uint8_t routing_id[2]; |
| uint8_t reserved2[20]; |
| }; |
| |
| struct scsi_log_sense |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| #define SLS_SP 0x01 |
| #define SLS_PPC 0x02 |
| u_int8_t page; |
| #define SLS_PAGE_CODE 0x3F |
| #define SLS_SUPPORTED_PAGES_PAGE 0x00 |
| #define SLS_OVERRUN_PAGE 0x01 |
| #define SLS_ERROR_WRITE_PAGE 0x02 |
| #define SLS_ERROR_READ_PAGE 0x03 |
| #define SLS_ERROR_READREVERSE_PAGE 0x04 |
| #define SLS_ERROR_VERIFY_PAGE 0x05 |
| #define SLS_ERROR_NONMEDIUM_PAGE 0x06 |
| #define SLS_ERROR_LASTN_PAGE 0x07 |
| #define SLS_LOGICAL_BLOCK_PROVISIONING 0x0c |
| #define SLS_SELF_TEST_PAGE 0x10 |
| #define SLS_STAT_AND_PERF 0x19 |
| #define SLS_IE_PAGE 0x2f |
| #define SLS_PAGE_CTRL_MASK 0xC0 |
| #define SLS_PAGE_CTRL_THRESHOLD 0x00 |
| #define SLS_PAGE_CTRL_CUMULATIVE 0x40 |
| #define SLS_PAGE_CTRL_THRESH_DEFAULT 0x80 |
| #define SLS_PAGE_CTRL_CUMUL_DEFAULT 0xC0 |
| u_int8_t subpage; |
| #define SLS_SUPPORTED_SUBPAGES_SUBPAGE 0xff |
| u_int8_t reserved; |
| u_int8_t paramptr[2]; |
| u_int8_t length[2]; |
| u_int8_t control; |
| }; |
| |
| struct scsi_log_select |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| /* SLS_SP 0x01 */ |
| #define SLS_PCR 0x02 |
| u_int8_t page; |
| /* SLS_PAGE_CTRL_MASK 0xC0 */ |
| /* SLS_PAGE_CTRL_THRESHOLD 0x00 */ |
| /* SLS_PAGE_CTRL_CUMULATIVE 0x40 */ |
| /* SLS_PAGE_CTRL_THRESH_DEFAULT 0x80 */ |
| /* SLS_PAGE_CTRL_CUMUL_DEFAULT 0xC0 */ |
| u_int8_t reserved[4]; |
| u_int8_t length[2]; |
| u_int8_t control; |
| }; |
| |
| struct scsi_log_header |
| { |
| u_int8_t page; |
| #define SL_PAGE_CODE 0x3F |
| #define SL_SPF 0x40 |
| #define SL_DS 0x80 |
| u_int8_t subpage; |
| u_int8_t datalen[2]; |
| }; |
| |
| struct scsi_log_param_header { |
| u_int8_t param_code[2]; |
| u_int8_t param_control; |
| #define SLP_LP 0x01 |
| #define SLP_LBIN 0x02 |
| #define SLP_TMC_MASK 0x0C |
| #define SLP_TMC_ALWAYS 0x00 |
| #define SLP_TMC_EQUAL 0x04 |
| #define SLP_TMC_NOTEQUAL 0x08 |
| #define SLP_TMC_GREATER 0x0C |
| #define SLP_ETC 0x10 |
| #define SLP_TSD 0x20 |
| #define SLP_DS 0x40 |
| #define SLP_DU 0x80 |
| u_int8_t param_len; |
| }; |
| |
| struct scsi_log_stat_and_perf { |
| struct scsi_log_param_header hdr; |
| #define SLP_SAP 0x0001 |
| uint8_t read_num[8]; |
| uint8_t write_num[8]; |
| uint8_t recvieved_lba[8]; |
| uint8_t transmitted_lba[8]; |
| uint8_t read_int[8]; |
| uint8_t write_int[8]; |
| uint8_t weighted_num[8]; |
| uint8_t weighted_int[8]; |
| }; |
| |
| struct scsi_log_idle_time { |
| struct scsi_log_param_header hdr; |
| #define SLP_IT 0x0002 |
| uint8_t idle_int[8]; |
| }; |
| |
| struct scsi_log_time_interval { |
| struct scsi_log_param_header hdr; |
| #define SLP_TI 0x0003 |
| uint8_t exponent[4]; |
| uint8_t integer[4]; |
| }; |
| |
| struct scsi_log_fua_stat_and_perf { |
| struct scsi_log_param_header hdr; |
| #define SLP_FUA_SAP 0x0004 |
| uint8_t fua_read_num[8]; |
| uint8_t fua_write_num[8]; |
| uint8_t fuanv_read_num[8]; |
| uint8_t fuanv_write_num[8]; |
| uint8_t fua_read_int[8]; |
| uint8_t fua_write_int[8]; |
| uint8_t fuanv_read_int[8]; |
| uint8_t fuanv_write_int[8]; |
| }; |
| |
| struct scsi_control_page { |
| u_int8_t page_code; |
| u_int8_t page_length; |
| u_int8_t rlec; |
| #define SCP_RLEC 0x01 /*Report Log Exception Cond*/ |
| #define SCP_GLTSD 0x02 /*Global Logging target |
| save disable */ |
| #define SCP_DSENSE 0x04 /*Descriptor Sense */ |
| #define SCP_DPICZ 0x08 /*Disable Prot. Info Check |
| if Prot. Field is Zero */ |
| #define SCP_TMF_ONLY 0x10 /*TM Functions Only*/ |
| #define SCP_TST_MASK 0xE0 /*Task Set Type Mask*/ |
| #define SCP_TST_ONE 0x00 /*One Task Set*/ |
| #define SCP_TST_SEPARATE 0x20 /*Separate Task Sets*/ |
| u_int8_t queue_flags; |
| #define SCP_QUEUE_ALG_MASK 0xF0 |
| #define SCP_QUEUE_ALG_RESTRICTED 0x00 |
| #define SCP_QUEUE_ALG_UNRESTRICTED 0x10 |
| #define SCP_NUAR 0x08 /*No UA on release*/ |
| #define SCP_QUEUE_ERR 0x02 /*Queued I/O aborted for CACs*/ |
| #define SCP_QUEUE_DQUE 0x01 /*Queued I/O disabled*/ |
| u_int8_t eca_and_aen; |
| #define SCP_EECA 0x80 /*Enable Extended CA*/ |
| #define SCP_RAC 0x40 /*Report a check*/ |
| #define SCP_SWP 0x08 /*Software Write Protect*/ |
| #define SCP_RAENP 0x04 /*Ready AEN Permission*/ |
| #define SCP_UAAENP 0x02 /*UA AEN Permission*/ |
| #define SCP_EAENP 0x01 /*Error AEN Permission*/ |
| u_int8_t flags4; |
| #define SCP_ATO 0x80 /*Application tag owner*/ |
| #define SCP_TAS 0x40 /*Task aborted status*/ |
| #define SCP_ATMPE 0x20 /*Application tag mode page*/ |
| #define SCP_RWWP 0x10 /*Reject write without prot*/ |
| u_int8_t aen_holdoff_period[2]; |
| u_int8_t busy_timeout_period[2]; |
| u_int8_t extended_selftest_completion_time[2]; |
| }; |
| |
| struct scsi_control_ext_page { |
| uint8_t page_code; |
| uint8_t subpage_code; |
| uint8_t page_length[2]; |
| uint8_t flags; |
| #define SCEP_TCMOS 0x04 /* Timestamp Changeable by */ |
| #define SCEP_SCSIP 0x02 /* SCSI Precedence (clock) */ |
| #define SCEP_IALUAE 0x01 /* Implicit ALUA Enabled */ |
| uint8_t prio; |
| uint8_t max_sense; |
| uint8_t reserve[25]; |
| }; |
| |
| struct scsi_cache_page { |
| u_int8_t page_code; |
| #define SCHP_PAGE_SAVABLE 0x80 /* Page is savable */ |
| u_int8_t page_length; |
| u_int8_t cache_flags; |
| #define SCHP_FLAGS_WCE 0x04 /* Write Cache Enable */ |
| #define SCHP_FLAGS_MF 0x02 /* Multiplication factor */ |
| #define SCHP_FLAGS_RCD 0x01 /* Read Cache Disable */ |
| u_int8_t rw_cache_policy; |
| u_int8_t dis_prefetch[2]; |
| u_int8_t min_prefetch[2]; |
| u_int8_t max_prefetch[2]; |
| u_int8_t max_prefetch_ceil[2]; |
| }; |
| |
| /* |
| * XXX KDM |
| * Updated version of the cache page, as of SBC. Update this to SBC-3 and |
| * rationalize the two. |
| */ |
| struct scsi_caching_page { |
| uint8_t page_code; |
| #define SMS_CACHING_PAGE 0x08 |
| uint8_t page_length; |
| uint8_t flags1; |
| #define SCP_IC 0x80 |
| #define SCP_ABPF 0x40 |
| #define SCP_CAP 0x20 |
| #define SCP_DISC 0x10 |
| #define SCP_SIZE 0x08 |
| #define SCP_WCE 0x04 |
| #define SCP_MF 0x02 |
| #define SCP_RCD 0x01 |
| uint8_t ret_priority; |
| uint8_t disable_pf_transfer_len[2]; |
| uint8_t min_prefetch[2]; |
| uint8_t max_prefetch[2]; |
| uint8_t max_pf_ceiling[2]; |
| uint8_t flags2; |
| #define SCP_FSW 0x80 |
| #define SCP_LBCSS 0x40 |
| #define SCP_DRA 0x20 |
| #define SCP_VS1 0x10 |
| #define SCP_VS2 0x08 |
| uint8_t cache_segments; |
| uint8_t cache_seg_size[2]; |
| uint8_t reserved; |
| uint8_t non_cache_seg_size[3]; |
| }; |
| |
| /* |
| * XXX KDM move this off to a vendor shim. |
| */ |
| struct copan_debugconf_subpage { |
| uint8_t page_code; |
| #define DBGCNF_PAGE_CODE 0x00 |
| uint8_t subpage; |
| #define DBGCNF_SUBPAGE_CODE 0xF0 |
| uint8_t page_length[2]; |
| uint8_t page_version; |
| #define DBGCNF_VERSION 0x00 |
| uint8_t ctl_time_io_secs[2]; |
| }; |
| |
| |
| struct scsi_info_exceptions_page { |
| u_int8_t page_code; |
| #define SIEP_PAGE_SAVABLE 0x80 /* Page is savable */ |
| u_int8_t page_length; |
| u_int8_t info_flags; |
| #define SIEP_FLAGS_PERF 0x80 |
| #define SIEP_FLAGS_EBF 0x20 |
| #define SIEP_FLAGS_EWASC 0x10 |
| #define SIEP_FLAGS_DEXCPT 0x08 |
| #define SIEP_FLAGS_TEST 0x04 |
| #define SIEP_FLAGS_EBACKERR 0x02 |
| #define SIEP_FLAGS_LOGERR 0x01 |
| u_int8_t mrie; |
| u_int8_t interval_timer[4]; |
| u_int8_t report_count[4]; |
| }; |
| |
| struct scsi_logical_block_provisioning_page_descr { |
| uint8_t flags; |
| #define SLBPPD_ENABLED 0x80 |
| #define SLBPPD_TYPE_MASK 0x38 |
| #define SLBPPD_ARMING_MASK 0x07 |
| #define SLBPPD_ARMING_DEC 0x02 |
| #define SLBPPD_ARMING_INC 0x01 |
| uint8_t resource; |
| uint8_t reserved[2]; |
| uint8_t count[4]; |
| }; |
| |
| struct scsi_logical_block_provisioning_page { |
| uint8_t page_code; |
| uint8_t subpage_code; |
| uint8_t page_length[2]; |
| uint8_t flags; |
| #define SLBPP_SITUA 0x01 |
| uint8_t reserved[11]; |
| struct scsi_logical_block_provisioning_page_descr descr[0]; |
| }; |
| |
| /* |
| * SCSI protocol identifier values, current as of SPC4r36l. |
| */ |
| #define SCSI_PROTO_FC 0x00 /* Fibre Channel */ |
| #define SCSI_PROTO_SPI 0x01 /* Parallel SCSI */ |
| #define SCSI_PROTO_SSA 0x02 /* Serial Storage Arch. */ |
| #define SCSI_PROTO_1394 0x03 /* IEEE 1394 (Firewire) */ |
| #define SCSI_PROTO_RDMA 0x04 /* SCSI RDMA Protocol */ |
| #define SCSI_PROTO_ISCSI 0x05 /* Internet SCSI */ |
| #define SCSI_PROTO_iSCSI 0x05 /* Internet SCSI */ |
| #define SCSI_PROTO_SAS 0x06 /* SAS Serial SCSI Protocol */ |
| #define SCSI_PROTO_ADT 0x07 /* Automation/Drive Int. Trans. Prot.*/ |
| #define SCSI_PROTO_ADITP 0x07 /* Automation/Drive Int. Trans. Prot.*/ |
| #define SCSI_PROTO_ATA 0x08 /* AT Attachment Interface */ |
| #define SCSI_PROTO_UAS 0x09 /* USB Atached SCSI */ |
| #define SCSI_PROTO_SOP 0x0a /* SCSI over PCI Express */ |
| #define SCSI_PROTO_NONE 0x0f /* No specific protocol */ |
| |
| struct scsi_proto_specific_page { |
| u_int8_t page_code; |
| #define SPSP_PAGE_SAVABLE 0x80 /* Page is savable */ |
| u_int8_t page_length; |
| u_int8_t protocol; |
| #define SPSP_PROTO_FC SCSI_PROTO_FC |
| #define SPSP_PROTO_SPI SCSI_PROTO_SPI |
| #define SPSP_PROTO_SSA SCSI_PROTO_SSA |
| #define SPSP_PROTO_1394 SCSI_PROTO_1394 |
| #define SPSP_PROTO_RDMA SCSI_PROTO_RDMA |
| #define SPSP_PROTO_ISCSI SCSI_PROTO_ISCSI |
| #define SPSP_PROTO_SAS SCSI_PROTO_SAS |
| #define SPSP_PROTO_ADT SCSI_PROTO_ADITP |
| #define SPSP_PROTO_ATA SCSI_PROTO_ATA |
| #define SPSP_PROTO_UAS SCSI_PROTO_UAS |
| #define SPSP_PROTO_SOP SCSI_PROTO_SOP |
| #define SPSP_PROTO_NONE SCSI_PROTO_NONE |
| }; |
| |
| struct scsi_reserve |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| #define SR_EXTENT 0x01 |
| #define SR_ID_MASK 0x0e |
| #define SR_3RDPTY 0x10 |
| #define SR_LUN_MASK 0xe0 |
| u_int8_t resv_id; |
| u_int8_t length[2]; |
| u_int8_t control; |
| }; |
| |
| struct scsi_reserve_10 { |
| uint8_t opcode; |
| uint8_t byte2; |
| #define SR10_3RDPTY 0x10 |
| #define SR10_LONGID 0x02 |
| #define SR10_EXTENT 0x01 |
| uint8_t resv_id; |
| uint8_t thirdparty_id; |
| uint8_t reserved[3]; |
| uint8_t length[2]; |
| uint8_t control; |
| }; |
| |
| |
| struct scsi_release |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| u_int8_t resv_id; |
| u_int8_t unused[1]; |
| u_int8_t length; |
| u_int8_t control; |
| }; |
| |
| struct scsi_release_10 { |
| uint8_t opcode; |
| uint8_t byte2; |
| uint8_t resv_id; |
| uint8_t thirdparty_id; |
| uint8_t reserved[3]; |
| uint8_t length[2]; |
| uint8_t control; |
| }; |
| |
| struct scsi_prevent |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| u_int8_t unused[2]; |
| u_int8_t how; |
| u_int8_t control; |
| }; |
| #define PR_PREVENT 0x01 |
| #define PR_ALLOW 0x00 |
| |
| struct scsi_sync_cache |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| #define SSC_IMMED 0x02 |
| #define SSC_RELADR 0x01 |
| u_int8_t begin_lba[4]; |
| u_int8_t reserved; |
| u_int8_t lb_count[2]; |
| u_int8_t control; |
| }; |
| |
| struct scsi_sync_cache_16 |
| { |
| uint8_t opcode; |
| uint8_t byte2; |
| uint8_t begin_lba[8]; |
| uint8_t lb_count[4]; |
| uint8_t reserved; |
| uint8_t control; |
| }; |
| |
| struct scsi_format { |
| uint8_t opcode; |
| uint8_t byte2; |
| #define SF_LONGLIST 0x20 |
| #define SF_FMTDATA 0x10 |
| #define SF_CMPLIST 0x08 |
| #define SF_FORMAT_MASK 0x07 |
| #define SF_FORMAT_BLOCK 0x00 |
| #define SF_FORMAT_LONG_BLOCK 0x03 |
| #define SF_FORMAT_BFI 0x04 |
| #define SF_FORMAT_PHYS 0x05 |
| uint8_t vendor; |
| uint8_t interleave[2]; |
| uint8_t control; |
| }; |
| |
| struct scsi_format_header_short { |
| uint8_t reserved; |
| #define SF_DATA_FOV 0x80 |
| #define SF_DATA_DPRY 0x40 |
| #define SF_DATA_DCRT 0x20 |
| #define SF_DATA_STPF 0x10 |
| #define SF_DATA_IP 0x08 |
| #define SF_DATA_DSP 0x04 |
| #define SF_DATA_IMMED 0x02 |
| #define SF_DATA_VS 0x01 |
| uint8_t byte2; |
| uint8_t defect_list_len[2]; |
| }; |
| |
| struct scsi_format_header_long { |
| uint8_t reserved; |
| uint8_t byte2; |
| uint8_t reserved2[2]; |
| uint8_t defect_list_len[4]; |
| }; |
| |
| struct scsi_changedef |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| u_int8_t unused1; |
| u_int8_t how; |
| u_int8_t unused[4]; |
| u_int8_t datalen; |
| u_int8_t control; |
| }; |
| |
| struct scsi_read_buffer |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| #define RWB_MODE 0x1F |
| #define RWB_MODE_HDR_DATA 0x00 |
| #define RWB_MODE_VENDOR 0x01 |
| #define RWB_MODE_DATA 0x02 |
| #define RWB_MODE_DESCR 0x03 |
| #define RWB_MODE_DOWNLOAD 0x04 |
| #define RWB_MODE_DOWNLOAD_SAVE 0x05 |
| #define RWB_MODE_ECHO 0x0A |
| #define RWB_MODE_ECHO_DESCR 0x0B |
| #define RWB_MODE_ERROR_HISTORY 0x1C |
| u_int8_t buffer_id; |
| u_int8_t offset[3]; |
| u_int8_t length[3]; |
| u_int8_t control; |
| }; |
| |
| struct scsi_read_buffer_16 |
| { |
| uint8_t opcode; |
| uint8_t byte2; |
| uint8_t offset[8]; |
| uint8_t length[4]; |
| uint8_t buffer_id; |
| uint8_t control; |
| }; |
| |
| struct scsi_write_buffer |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| u_int8_t buffer_id; |
| u_int8_t offset[3]; |
| u_int8_t length[3]; |
| u_int8_t control; |
| }; |
| |
| struct scsi_read_attribute |
| { |
| u_int8_t opcode; |
| u_int8_t service_action; |
| #define SRA_SA_ATTR_VALUES 0x00 |
| #define SRA_SA_ATTR_LIST 0x01 |
| #define SRA_SA_LOG_VOL_LIST 0x02 |
| #define SRA_SA_PART_LIST 0x03 |
| #define SRA_SA_RESTRICTED 0x04 |
| #define SRA_SA_SUPPORTED_ATTRS 0x05 |
| #define SRA_SA_MASK 0x1f |
| u_int8_t element[2]; |
| u_int8_t elem_type; |
| u_int8_t logical_volume; |
| u_int8_t reserved1; |
| u_int8_t partition; |
| u_int8_t first_attribute[2]; |
| u_int8_t length[4]; |
| u_int8_t cache; |
| #define SRA_CACHE 0x01 |
| u_int8_t control; |
| }; |
| |
| struct scsi_write_attribute |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| #define SWA_WTC 0x01 |
| u_int8_t element[3]; |
| u_int8_t logical_volume; |
| u_int8_t reserved1; |
| u_int8_t partition; |
| u_int8_t reserved2[2]; |
| u_int8_t length[4]; |
| u_int8_t reserved3; |
| u_int8_t control; |
| }; |
| |
| |
| struct scsi_read_attribute_values |
| { |
| u_int8_t length[4]; |
| u_int8_t attribute_0[0]; |
| }; |
| |
| struct scsi_mam_attribute_header |
| { |
| u_int8_t id[2]; |
| /* |
| * Attributes obtained from SPC-4r36g (section 7.4.2.2) and |
| * SSC-4r03 (section 4.2.21). |
| */ |
| #define SMA_ATTR_ID_DEVICE_MIN 0x0000 |
| |
| #define SMA_ATTR_REM_CAP_PARTITION 0x0000 |
| #define SMA_ATTR_MAX_CAP_PARTITION 0x0001 |
| #define SMA_ATTR_TAPEALERT_FLAGS 0x0002 |
| #define SMA_ATTR_LOAD_COUNT 0x0003 |
| #define SMA_ATTR_MAM_SPACE_REMAINING 0x0004 |
| |
| #define SMA_ATTR_DEV_ASSIGNING_ORG 0x0005 |
| #define SMA_ATTR_FORMAT_DENSITY_CODE 0x0006 |
| #define SMA_ATTR_INITIALIZATION_COUNT 0x0007 |
| #define SMA_ATTR_VOLUME_ID 0x0008 |
| #define SMA_ATTR_VOLUME_CHANGE_REF 0x0009 |
| |
| #define SMA_ATTR_DEV_SERIAL_LAST_LOAD 0x020a |
| #define SMA_ATTR_DEV_SERIAL_LAST_LOAD_1 0x020b |
| #define SMA_ATTR_DEV_SERIAL_LAST_LOAD_2 0x020c |
| #define SMA_ATTR_DEV_SERIAL_LAST_LOAD_3 0x020d |
| |
| #define SMA_ATTR_TOTAL_MB_WRITTEN_LT 0x0220 |
| #define SMA_ATTR_TOTAL_MB_READ_LT 0x0221 |
| #define SMA_ATTR_TOTAL_MB_WRITTEN_CUR 0x0222 |
| #define SMA_ATTR_TOTAL_MB_READ_CUR 0x0223 |
| #define SMA_ATTR_FIRST_ENC_BLOCK 0x0224 |
| #define SMA_ATTR_NEXT_UNENC_BLOCK 0x0225 |
| |
| #define SMA_ATTR_MEDIUM_USAGE_HIST 0x0340 |
| #define SMA_ATTR_PART_USAGE_HIST 0x0341 |
| |
| #define SMA_ATTR_ID_DEVICE_MAX 0x03ff |
| |
| #define SMA_ATTR_ID_MEDIUM_MIN 0x0400 |
| |
| #define SMA_ATTR_MED_MANUF 0x0400 |
| #define SMA_ATTR_MED_SERIAL 0x0401 |
| |
| #define SMA_ATTR_MED_LENGTH 0x0402 |
| #define SMA_ATTR_MED_WIDTH 0x0403 |
| #define SMA_ATTR_MED_ASSIGNING_ORG 0x0404 |
| #define SMA_ATTR_MED_DENSITY_CODE 0x0405 |
| |
| #define SMA_ATTR_MED_MANUF_DATE 0x0406 |
| #define SMA_ATTR_MAM_CAPACITY 0x0407 |
| #define SMA_ATTR_MED_TYPE 0x0408 |
| #define SMA_ATTR_MED_TYPE_INFO 0x0409 |
| #define SMA_ATTR_MED_SERIAL_NUM 0x040a |
| |
| #define SMA_ATTR_ID_MEDIUM_MAX 0x07ff |
| |
| #define SMA_ATTR_ID_HOST_MIN 0x0800 |
| |
| #define SMA_ATTR_APP_VENDOR 0x0800 |
| #define SMA_ATTR_APP_NAME 0x0801 |
| #define SMA_ATTR_APP_VERSION 0x0802 |
| #define SMA_ATTR_USER_MED_TEXT_LABEL 0x0803 |
| #define SMA_ATTR_LAST_WRITTEN_TIME 0x0804 |
| #define SMA_ATTR_TEXT_LOCAL_ID 0x0805 |
| #define SMA_ATTR_BARCODE 0x0806 |
| #define SMA_ATTR_HOST_OWNER_NAME 0x0807 |
| #define SMA_ATTR_MEDIA_POOL 0x0808 |
| #define SMA_ATTR_PART_USER_LABEL 0x0809 |
| #define SMA_ATTR_LOAD_UNLOAD_AT_PART 0x080a |
| #define SMA_ATTR_APP_FORMAT_VERSION 0x080b |
| #define SMA_ATTR_VOL_COHERENCY_INFO 0x080c |
| |
| #define SMA_ATTR_ID_HOST_MAX 0x0bff |
| |
| #define SMA_ATTR_VENDOR_DEVICE_MIN 0x0c00 |
| #define SMA_ATTR_VENDOR_DEVICE_MAX 0x0fff |
| #define SMA_ATTR_VENDOR_MEDIUM_MIN 0x1000 |
| #define SMA_ATTR_VENDOR_MEDIUM_MAX 0x13ff |
| #define SMA_ATTR_VENDOR_HOST_MIN 0x1400 |
| #define SMA_ATTR_VENDOR_HOST_MAX 0x17ff |
| u_int8_t byte2; |
| #define SMA_FORMAT_BINARY 0x00 |
| #define SMA_FORMAT_ASCII 0x01 |
| #define SMA_FORMAT_TEXT 0x02 |
| #define SMA_FORMAT_MASK 0x03 |
| #define SMA_READ_ONLY 0x80 |
| u_int8_t length[2]; |
| u_int8_t attribute[0]; |
| }; |
| |
| struct scsi_attrib_list_header { |
| u_int8_t length[4]; |
| u_int8_t first_attr_0[0]; |
| }; |
| |
| struct scsi_attrib_lv_list { |
| u_int8_t length[2]; |
| u_int8_t first_lv_number; |
| u_int8_t num_logical_volumes; |
| }; |
| |
| struct scsi_attrib_vendser { |
| uint8_t vendor[8]; |
| uint8_t serial_num[32]; |
| }; |
| |
| /* |
| * These values are used to decode the Volume Coherency Information |
| * Attribute (0x080c) for LTFS-format coherency information. |
| * Although the Application Client Specific lengths are different for |
| * Version 0 and Version 1, the data is in fact the same. The length |
| * difference was due to a code bug. |
| */ |
| #define SCSI_LTFS_VER0_LEN 42 |
| #define SCSI_LTFS_VER1_LEN 43 |
| #define SCSI_LTFS_UUID_LEN 36 |
| #define SCSI_LTFS_STR_NAME "LTFS" |
| #define SCSI_LTFS_STR_LEN 4 |
| |
| typedef enum { |
| SCSI_ATTR_FLAG_NONE = 0x00, |
| SCSI_ATTR_FLAG_HEX = 0x01, |
| SCSI_ATTR_FLAG_FP = 0x02, |
| SCSI_ATTR_FLAG_DIV_10 = 0x04, |
| SCSI_ATTR_FLAG_FP_1DIGIT = 0x08 |
| } scsi_attrib_flags; |
| |
| typedef enum { |
| SCSI_ATTR_OUTPUT_NONE = 0x00, |
| SCSI_ATTR_OUTPUT_TEXT_MASK = 0x03, |
| SCSI_ATTR_OUTPUT_TEXT_RAW = 0x00, |
| SCSI_ATTR_OUTPUT_TEXT_ESC = 0x01, |
| SCSI_ATTR_OUTPUT_TEXT_RSV1 = 0x02, |
| SCSI_ATTR_OUTPUT_TEXT_RSV2 = 0x03, |
| SCSI_ATTR_OUTPUT_NONASCII_MASK = 0x0c, |
| SCSI_ATTR_OUTPUT_NONASCII_TRIM = 0x00, |
| SCSI_ATTR_OUTPUT_NONASCII_ESC = 0x04, |
| SCSI_ATTR_OUTPUT_NONASCII_RAW = 0x08, |
| SCSI_ATTR_OUTPUT_NONASCII_RSV1 = 0x0c, |
| SCSI_ATTR_OUTPUT_FIELD_MASK = 0xf0, |
| SCSI_ATTR_OUTPUT_FIELD_ALL = 0xf0, |
| SCSI_ATTR_OUTPUT_FIELD_NONE = 0x00, |
| SCSI_ATTR_OUTPUT_FIELD_DESC = 0x10, |
| SCSI_ATTR_OUTPUT_FIELD_NUM = 0x20, |
| SCSI_ATTR_OUTPUT_FIELD_SIZE = 0x40, |
| SCSI_ATTR_OUTPUT_FIELD_RW = 0x80 |
| } scsi_attrib_output_flags; |
| |
| struct sbuf; |
| |
| struct scsi_attrib_table_entry |
| { |
| u_int32_t id; |
| u_int32_t flags; |
| const char *desc; |
| const char *suffix; |
| int (*to_str)(struct sbuf *sb, struct scsi_mam_attribute_header *hdr, |
| uint32_t valid_len, uint32_t flags, |
| uint32_t output_flags, char *error_str, |
| int error_str_len); |
| int (*parse_str)(char *str, struct scsi_mam_attribute_header *hdr, |
| uint32_t alloc_len, uint32_t flags, char *error_str, |
| int error_str_len); |
| }; |
| |
| struct scsi_rw_6 |
| { |
| u_int8_t opcode; |
| u_int8_t addr[3]; |
| /* only 5 bits are valid in the MSB address byte */ |
| #define SRW_TOPADDR 0x1F |
| u_int8_t length; |
| u_int8_t control; |
| }; |
| |
| struct scsi_rw_10 |
| { |
| u_int8_t opcode; |
| #define SRW10_RELADDR 0x01 |
| /* EBP defined for WRITE(10) only */ |
| #define SRW10_EBP 0x04 |
| #define SRW10_FUA 0x08 |
| #define SRW10_DPO 0x10 |
| u_int8_t byte2; |
| u_int8_t addr[4]; |
| u_int8_t reserved; |
| u_int8_t length[2]; |
| u_int8_t control; |
| }; |
| |
| struct scsi_rw_12 |
| { |
| u_int8_t opcode; |
| #define SRW12_RELADDR 0x01 |
| #define SRW12_FUA 0x08 |
| #define SRW12_DPO 0x10 |
| u_int8_t byte2; |
| u_int8_t addr[4]; |
| u_int8_t length[4]; |
| u_int8_t reserved; |
| u_int8_t control; |
| }; |
| |
| struct scsi_rw_16 |
| { |
| u_int8_t opcode; |
| #define SRW16_RELADDR 0x01 |
| #define SRW16_FUA 0x08 |
| #define SRW16_DPO 0x10 |
| u_int8_t byte2; |
| u_int8_t addr[8]; |
| u_int8_t length[4]; |
| u_int8_t reserved; |
| u_int8_t control; |
| }; |
| |
| struct scsi_write_atomic_16 |
| { |
| uint8_t opcode; |
| uint8_t byte2; |
| uint8_t addr[8]; |
| uint8_t boundary[2]; |
| uint8_t length[2]; |
| uint8_t group; |
| uint8_t control; |
| }; |
| |
| struct scsi_write_same_10 |
| { |
| uint8_t opcode; |
| uint8_t byte2; |
| #define SWS_LBDATA 0x02 |
| #define SWS_PBDATA 0x04 |
| #define SWS_UNMAP 0x08 |
| #define SWS_ANCHOR 0x10 |
| uint8_t addr[4]; |
| uint8_t group; |
| uint8_t length[2]; |
| uint8_t control; |
| }; |
| |
| struct scsi_write_same_16 |
| { |
| uint8_t opcode; |
| uint8_t byte2; |
| #define SWS_NDOB 0x01 |
| uint8_t addr[8]; |
| uint8_t length[4]; |
| uint8_t group; |
| uint8_t control; |
| }; |
| |
| struct scsi_unmap |
| { |
| uint8_t opcode; |
| uint8_t byte2; |
| #define SU_ANCHOR 0x01 |
| uint8_t reserved[4]; |
| uint8_t group; |
| uint8_t length[2]; |
| uint8_t control; |
| }; |
| |
| struct scsi_unmap_header |
| { |
| uint8_t length[2]; |
| uint8_t desc_length[2]; |
| uint8_t reserved[4]; |
| }; |
| |
| struct scsi_unmap_desc |
| { |
| uint8_t lba[8]; |
| uint8_t length[4]; |
| uint8_t reserved[4]; |
| }; |
| |
| struct scsi_write_verify_10 |
| { |
| uint8_t opcode; |
| uint8_t byte2; |
| #define SWV_BYTCHK 0x02 |
| #define SWV_DPO 0x10 |
| #define SWV_WRPROECT_MASK 0xe0 |
| uint8_t addr[4]; |
| uint8_t group; |
| uint8_t length[2]; |
| uint8_t control; |
| }; |
| |
| struct scsi_write_verify_12 |
| { |
| uint8_t opcode; |
| uint8_t byte2; |
| uint8_t addr[4]; |
| uint8_t length[4]; |
| uint8_t group; |
| uint8_t control; |
| }; |
| |
| struct scsi_write_verify_16 |
| { |
| uint8_t opcode; |
| uint8_t byte2; |
| uint8_t addr[8]; |
| uint8_t length[4]; |
| uint8_t group; |
| uint8_t control; |
| }; |
| |
| |
| struct scsi_start_stop_unit |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| #define SSS_IMMED 0x01 |
| u_int8_t reserved[2]; |
| u_int8_t how; |
| #define SSS_START 0x01 |
| #define SSS_LOEJ 0x02 |
| #define SSS_PC_MASK 0xf0 |
| #define SSS_PC_START_VALID 0x00 |
| #define SSS_PC_ACTIVE 0x10 |
| #define SSS_PC_IDLE 0x20 |
| #define SSS_PC_STANDBY 0x30 |
| #define SSS_PC_LU_CONTROL 0x70 |
| #define SSS_PC_FORCE_IDLE_0 0xa0 |
| #define SSS_PC_FORCE_STANDBY_0 0xb0 |
| u_int8_t control; |
| }; |
| |
| struct ata_pass_12 { |
| u_int8_t opcode; |
| u_int8_t protocol; |
| #define AP_PROTO_HARD_RESET (0x00 << 1) |
| #define AP_PROTO_SRST (0x01 << 1) |
| #define AP_PROTO_NON_DATA (0x03 << 1) |
| #define AP_PROTO_PIO_IN (0x04 << 1) |
| #define AP_PROTO_PIO_OUT (0x05 << 1) |
| #define AP_PROTO_DMA (0x06 << 1) |
| #define AP_PROTO_DMA_QUEUED (0x07 << 1) |
| #define AP_PROTO_DEVICE_DIAG (0x08 << 1) |
| #define AP_PROTO_DEVICE_RESET (0x09 << 1) |
| #define AP_PROTO_UDMA_IN (0x0a << 1) |
| #define AP_PROTO_UDMA_OUT (0x0b << 1) |
| #define AP_PROTO_FPDMA (0x0c << 1) |
| #define AP_PROTO_RESP_INFO (0x0f << 1) |
| #define AP_PROTO_MASK 0x1e |
| #define AP_MULTI 0xe0 |
| u_int8_t flags; |
| #define AP_T_LEN 0x03 |
| #define AP_BB 0x04 |
| #define AP_T_DIR 0x08 |
| #define AP_CK_COND 0x20 |
| #define AP_OFFLINE 0x60 |
| u_int8_t features; |
| u_int8_t sector_count; |
| u_int8_t lba_low; |
| u_int8_t lba_mid; |
| u_int8_t lba_high; |
| u_int8_t device; |
| u_int8_t command; |
| u_int8_t reserved; |
| u_int8_t control; |
| }; |
| |
| struct scsi_maintenance_in |
| { |
| uint8_t opcode; |
| uint8_t byte2; |
| #define SERVICE_ACTION_MASK 0x1f |
| #define SA_RPRT_TRGT_GRP 0x0a |
| uint8_t reserved[4]; |
| uint8_t length[4]; |
| uint8_t reserved1; |
| uint8_t control; |
| }; |
| |
| struct scsi_report_supported_opcodes |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| uint8_t options; |
| #define RSO_RCTD 0x80 |
| #define RSO_OPTIONS_MASK 0x07 |
| #define RSO_OPTIONS_ALL 0x00 |
| #define RSO_OPTIONS_OC 0x01 |
| #define RSO_OPTIONS_OC_SA 0x02 |
| uint8_t requested_opcode; |
| uint8_t requested_service_action[2]; |
| uint8_t length[4]; |
| uint8_t reserved1; |
| uint8_t control; |
| }; |
| |
| struct scsi_report_supported_opcodes_timeout |
| { |
| uint8_t length[2]; |
| uint8_t reserved; |
| uint8_t cmd_specific; |
| uint8_t nominal_time[4]; |
| uint8_t recommended_time[4]; |
| }; |
| |
| struct scsi_report_supported_opcodes_descr |
| { |
| uint8_t opcode; |
| uint8_t reserved; |
| uint8_t service_action[2]; |
| uint8_t reserved2; |
| uint8_t flags; |
| #define RSO_SERVACTV 0x01 |
| #define RSO_CTDP 0x02 |
| uint8_t cdb_length[2]; |
| struct scsi_report_supported_opcodes_timeout timeout[0]; |
| }; |
| |
| struct scsi_report_supported_opcodes_all |
| { |
| uint8_t length[4]; |
| struct scsi_report_supported_opcodes_descr descr[0]; |
| }; |
| |
| struct scsi_report_supported_opcodes_one |
| { |
| uint8_t reserved; |
| uint8_t support; |
| #define RSO_ONE_CTDP 0x80 |
| #define RSO_ONE_SUP_MASK 0x07 |
| #define RSO_ONE_SUP_UNAVAIL 0x00 |
| #define RSO_ONE_SUP_NOT_SUP 0x01 |
| #define RSO_ONE_SUP_AVAIL 0x03 |
| #define RSO_ONE_SUP_VENDOR 0x05 |
| uint8_t cdb_length[2]; |
| uint8_t cdb_usage[]; |
| }; |
| |
| struct scsi_report_supported_tmf |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| uint8_t reserved[4]; |
| uint8_t length[4]; |
| uint8_t reserved1; |
| uint8_t control; |
| }; |
| |
| struct scsi_report_supported_tmf_data |
| { |
| uint8_t byte1; |
| #define RST_WAKES 0x01 |
| #define RST_TRS 0x02 |
| #define RST_QTS 0x04 |
| #define RST_LURS 0x08 |
| #define RST_CTSS 0x10 |
| #define RST_CACAS 0x20 |
| #define RST_ATSS 0x40 |
| #define RST_ATS 0x80 |
| uint8_t byte2; |
| #define RST_ITNRS 0x01 |
| #define RST_QTSS 0x02 |
| #define RST_QAES 0x04 |
| uint8_t reserved[2]; |
| }; |
| |
| struct scsi_report_timestamp |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| uint8_t reserved[4]; |
| uint8_t length[4]; |
| uint8_t reserved1; |
| uint8_t control; |
| }; |
| |
| struct scsi_report_timestamp_data |
| { |
| uint8_t length[2]; |
| uint8_t origin; |
| #define RTS_ORIG_MASK 0x00 |
| #define RTS_ORIG_ZERO 0x00 |
| #define RTS_ORIG_SET 0x02 |
| #define RTS_ORIG_OUTSIDE 0x03 |
| uint8_t reserved; |
| uint8_t timestamp[6]; |
| uint8_t reserve2[2]; |
| }; |
| |
| struct scsi_receive_copy_status_lid1 |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| #define RCS_RCS_LID1 0x00 |
| uint8_t list_identifier; |
| uint8_t reserved[7]; |
| uint8_t length[4]; |
| uint8_t reserved1; |
| uint8_t control; |
| }; |
| |
| struct scsi_receive_copy_status_lid1_data |
| { |
| uint8_t available_data[4]; |
| uint8_t copy_command_status; |
| #define RCS_CCS_INPROG 0x00 |
| #define RCS_CCS_COMPLETED 0x01 |
| #define RCS_CCS_ERROR 0x02 |
| uint8_t segments_processed[2]; |
| uint8_t transfer_count_units; |
| #define RCS_TC_BYTES 0x00 |
| #define RCS_TC_KBYTES 0x01 |
| #define RCS_TC_MBYTES 0x02 |
| #define RCS_TC_GBYTES 0x03 |
| #define RCS_TC_TBYTES 0x04 |
| #define RCS_TC_PBYTES 0x05 |
| #define RCS_TC_EBYTES 0x06 |
| #define RCS_TC_LBAS 0xf1 |
| uint8_t transfer_count[4]; |
| }; |
| |
| struct scsi_receive_copy_failure_details |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| #define RCS_RCFD 0x04 |
| uint8_t list_identifier; |
| uint8_t reserved[7]; |
| uint8_t length[4]; |
| uint8_t reserved1; |
| uint8_t control; |
| }; |
| |
| struct scsi_receive_copy_failure_details_data |
| { |
| uint8_t available_data[4]; |
| uint8_t reserved[52]; |
| uint8_t copy_command_status; |
| uint8_t reserved2; |
| uint8_t sense_data_length[2]; |
| uint8_t sense_data[]; |
| }; |
| |
| struct scsi_receive_copy_status_lid4 |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| #define RCS_RCS_LID4 0x05 |
| uint8_t list_identifier[4]; |
| uint8_t reserved[4]; |
| uint8_t length[4]; |
| uint8_t reserved1; |
| uint8_t control; |
| }; |
| |
| struct scsi_receive_copy_status_lid4_data |
| { |
| uint8_t available_data[4]; |
| uint8_t response_to_service_action; |
| uint8_t copy_command_status; |
| #define RCS_CCS_COMPLETED_PROD 0x03 |
| #define RCS_CCS_COMPLETED_RESID 0x04 |
| #define RCS_CCS_INPROG_FGBG 0x10 |
| #define RCS_CCS_INPROG_FG 0x11 |
| #define RCS_CCS_INPROG_BG 0x12 |
| #define RCS_CCS_ABORTED 0x60 |
| uint8_t operation_counter[2]; |
| uint8_t estimated_status_update_delay[4]; |
| uint8_t extended_copy_completion_status; |
| uint8_t length_of_the_sense_data_field; |
| uint8_t sense_data_length; |
| uint8_t transfer_count_units; |
| uint8_t transfer_count[8]; |
| uint8_t segments_processed[2]; |
| uint8_t reserved[6]; |
| uint8_t sense_data[]; |
| }; |
| |
| struct scsi_receive_copy_operating_parameters |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| #define RCS_RCOP 0x03 |
| uint8_t reserved[8]; |
| uint8_t length[4]; |
| uint8_t reserved1; |
| uint8_t control; |
| }; |
| |
| struct scsi_receive_copy_operating_parameters_data |
| { |
| uint8_t length[4]; |
| uint8_t snlid; |
| #define RCOP_SNLID 0x01 |
| uint8_t reserved[3]; |
| uint8_t maximum_cscd_descriptor_count[2]; |
| uint8_t maximum_segment_descriptor_count[2]; |
| uint8_t maximum_descriptor_list_length[4]; |
| uint8_t maximum_segment_length[4]; |
| uint8_t maximum_inline_data_length[4]; |
| uint8_t held_data_limit[4]; |
| uint8_t maximum_stream_device_transfer_size[4]; |
| uint8_t reserved2[2]; |
| uint8_t total_concurrent_copies[2]; |
| uint8_t maximum_concurrent_copies; |
| uint8_t data_segment_granularity; |
| uint8_t inline_data_granularity; |
| uint8_t held_data_granularity; |
| uint8_t reserved3[3]; |
| uint8_t implemented_descriptor_list_length; |
| uint8_t list_of_implemented_descriptor_type_codes[0]; |
| }; |
| |
| struct scsi_extended_copy |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| #define EC_EC_LID1 0x00 |
| #define EC_EC_LID4 0x01 |
| uint8_t reserved[8]; |
| uint8_t length[4]; |
| uint8_t reserved1; |
| uint8_t control; |
| }; |
| |
| struct scsi_ec_cscd_dtsp |
| { |
| uint8_t flags; |
| #define EC_CSCD_FIXED 0x01 |
| #define EC_CSCD_PAD 0x04 |
| uint8_t block_length[3]; |
| }; |
| |
| struct scsi_ec_cscd |
| { |
| uint8_t type_code; |
| #define EC_CSCD_EXT 0xff |
| uint8_t luidt_pdt; |
| #define EC_NUL 0x20 |
| #define EC_LUIDT_MASK 0xc0 |
| #define EC_LUIDT_LUN 0x00 |
| #define EC_LUIDT_PROXY_TOKEN 0x40 |
| uint8_t relative_initiator_port[2]; |
| uint8_t cscd_params[24]; |
| struct scsi_ec_cscd_dtsp dtsp; |
| }; |
| |
| struct scsi_ec_cscd_id |
| { |
| uint8_t type_code; |
| #define EC_CSCD_ID 0xe4 |
| uint8_t luidt_pdt; |
| uint8_t relative_initiator_port[2]; |
| uint8_t codeset; |
| uint8_t id_type; |
| uint8_t reserved; |
| uint8_t length; |
| uint8_t designator[20]; |
| struct scsi_ec_cscd_dtsp dtsp; |
| }; |
| |
| struct scsi_ec_segment |
| { |
| uint8_t type_code; |
| uint8_t flags; |
| #define EC_SEG_DC 0x02 |
| #define EC_SEG_CAT 0x01 |
| uint8_t descr_length[2]; |
| uint8_t params[]; |
| }; |
| |
| struct scsi_ec_segment_b2b |
| { |
| uint8_t type_code; |
| #define EC_SEG_B2B 0x02 |
| uint8_t flags; |
| uint8_t descr_length[2]; |
| uint8_t src_cscd[2]; |
| uint8_t dst_cscd[2]; |
| uint8_t reserved[2]; |
| uint8_t number_of_blocks[2]; |
| uint8_t src_lba[8]; |
| uint8_t dst_lba[8]; |
| }; |
| |
| struct scsi_ec_segment_verify |
| { |
| uint8_t type_code; |
| #define EC_SEG_VERIFY 0x07 |
| uint8_t reserved; |
| uint8_t descr_length[2]; |
| uint8_t src_cscd[2]; |
| uint8_t reserved2[2]; |
| uint8_t tur; |
| uint8_t reserved3[3]; |
| }; |
| |
| struct scsi_ec_segment_register_key |
| { |
| uint8_t type_code; |
| #define EC_SEG_REGISTER_KEY 0x14 |
| uint8_t reserved; |
| uint8_t descr_length[2]; |
| uint8_t reserved2[2]; |
| uint8_t dst_cscd[2]; |
| uint8_t res_key[8]; |
| uint8_t sa_res_key[8]; |
| uint8_t reserved3[4]; |
| }; |
| |
| struct scsi_extended_copy_lid1_data |
| { |
| uint8_t list_identifier; |
| uint8_t flags; |
| #define EC_PRIORITY 0x07 |
| #define EC_LIST_ID_USAGE_MASK 0x18 |
| #define EC_LIST_ID_USAGE_FULL 0x08 |
| #define EC_LIST_ID_USAGE_NOHOLD 0x10 |
| #define EC_LIST_ID_USAGE_NONE 0x18 |
| #define EC_STR 0x20 |
| uint8_t cscd_list_length[2]; |
| uint8_t reserved[4]; |
| uint8_t segment_list_length[4]; |
| uint8_t inline_data_length[4]; |
| uint8_t data[]; |
| }; |
| |
| struct scsi_extended_copy_lid4_data |
| { |
| uint8_t list_format; |
| #define EC_LIST_FORMAT 0x01 |
| uint8_t flags; |
| uint8_t header_cscd_list_length[2]; |
| uint8_t reserved[11]; |
| uint8_t flags2; |
| #define EC_IMMED 0x01 |
| #define EC_G_SENSE 0x02 |
| uint8_t header_cscd_type_code; |
| uint8_t reserved2[3]; |
| uint8_t list_identifier[4]; |
| uint8_t reserved3[18]; |
| uint8_t cscd_list_length[2]; |
| uint8_t segment_list_length[2]; |
| uint8_t inline_data_length[2]; |
| uint8_t data[]; |
| }; |
| |
| struct scsi_copy_operation_abort |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| #define EC_COA 0x1c |
| uint8_t list_identifier[4]; |
| uint8_t reserved[9]; |
| uint8_t control; |
| }; |
| |
| struct scsi_populate_token |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| #define EC_PT 0x10 |
| uint8_t reserved[4]; |
| uint8_t list_identifier[4]; |
| uint8_t length[4]; |
| uint8_t group_number; |
| uint8_t control; |
| }; |
| |
| struct scsi_range_desc |
| { |
| uint8_t lba[8]; |
| uint8_t length[4]; |
| uint8_t reserved[4]; |
| }; |
| |
| struct scsi_populate_token_data |
| { |
| uint8_t length[2]; |
| uint8_t flags; |
| #define EC_PT_IMMED 0x01 |
| #define EC_PT_RTV 0x02 |
| uint8_t reserved; |
| uint8_t inactivity_timeout[4]; |
| uint8_t rod_type[4]; |
| uint8_t reserved2[2]; |
| uint8_t range_descriptor_length[2]; |
| struct scsi_range_desc desc[]; |
| }; |
| |
| struct scsi_write_using_token |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| #define EC_WUT 0x11 |
| uint8_t reserved[4]; |
| uint8_t list_identifier[4]; |
| uint8_t length[4]; |
| uint8_t group_number; |
| uint8_t control; |
| }; |
| |
| struct scsi_write_using_token_data |
| { |
| uint8_t length[2]; |
| uint8_t flags; |
| #define EC_WUT_IMMED 0x01 |
| #define EC_WUT_DEL_TKN 0x02 |
| uint8_t reserved[5]; |
| uint8_t offset_into_rod[8]; |
| uint8_t rod_token[512]; |
| uint8_t reserved2[6]; |
| uint8_t range_descriptor_length[2]; |
| struct scsi_range_desc desc[]; |
| }; |
| |
| struct scsi_receive_rod_token_information |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| #define RCS_RRTI 0x07 |
| uint8_t list_identifier[4]; |
| uint8_t reserved[4]; |
| uint8_t length[4]; |
| uint8_t reserved2; |
| uint8_t control; |
| }; |
| |
| struct scsi_token |
| { |
| uint8_t type[4]; |
| #define ROD_TYPE_INTERNAL 0x00000000 |
| #define ROD_TYPE_AUR 0x00010000 |
| #define ROD_TYPE_PIT_DEF 0x00800000 |
| #define ROD_TYPE_PIT_VULN 0x00800001 |
| #define ROD_TYPE_PIT_PERS 0x00800002 |
| #define ROD_TYPE_PIT_ANY 0x0080FFFF |
| #define ROD_TYPE_BLOCK_ZERO 0xFFFF0001 |
| uint8_t reserved[2]; |
| uint8_t length[2]; |
| uint8_t body[0]; |
| }; |
| |
| struct scsi_report_all_rod_tokens |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| #define RCS_RART 0x08 |
| uint8_t reserved[8]; |
| uint8_t length[4]; |
| uint8_t reserved2; |
| uint8_t control; |
| }; |
| |
| struct scsi_report_all_rod_tokens_data |
| { |
| uint8_t available_data[4]; |
| uint8_t reserved[4]; |
| uint8_t rod_management_token_list[]; |
| }; |
| |
| struct ata_pass_16 { |
| u_int8_t opcode; |
| u_int8_t protocol; |
| #define AP_EXTEND 0x01 |
| u_int8_t flags; |
| #define AP_FLAG_TLEN_NO_DATA (0 << 0) |
| #define AP_FLAG_TLEN_FEAT (1 << 0) |
| #define AP_FLAG_TLEN_SECT_CNT (2 << 0) |
| #define AP_FLAG_TLEN_STPSIU (3 << 0) |
| #define AP_FLAG_BYT_BLOK_BYTES (0 << 2) |
| #define AP_FLAG_BYT_BLOK_BLOCKS (1 << 2) |
| #define AP_FLAG_TDIR_TO_DEV (0 << 3) |
| #define AP_FLAG_TDIR_FROM_DEV (1 << 3) |
| #define AP_FLAG_CHK_COND (1 << 5) |
| u_int8_t features_ext; |
| u_int8_t features; |
| u_int8_t sector_count_ext; |
| u_int8_t sector_count; |
| u_int8_t lba_low_ext; |
| u_int8_t lba_low; |
| u_int8_t lba_mid_ext; |
| u_int8_t lba_mid; |
| u_int8_t lba_high_ext; |
| u_int8_t lba_high; |
| u_int8_t device; |
| u_int8_t command; |
| u_int8_t control; |
| }; |
| |
| struct ata_pass_32 { |
| uint8_t opcode; |
| uint8_t control; |
| uint8_t reserved1[5]; |
| uint8_t length; |
| uint8_t service_action[2]; |
| #define ATA_PASS_32_SA 0x1ff0 |
| uint8_t protocol; |
| uint8_t flags; |
| uint8_t reserved2[2]; |
| uint8_t lba[6]; |
| uint8_t features[2]; |
| uint8_t count[2]; |
| uint8_t device; |
| uint8_t command; |
| uint8_t reserved3; |
| uint8_t icc; |
| uint8_t auxiliary[4]; |
| }; |
| |
| |
| #define SC_SCSI_1 0x01 |
| #define SC_SCSI_2 0x03 |
| |
| /* |
| * Opcodes |
| */ |
| |
| #define TEST_UNIT_READY 0x00 |
| #define REQUEST_SENSE 0x03 |
| #define READ_6 0x08 |
| #define WRITE_6 0x0A |
| #define INQUIRY 0x12 |
| #define MODE_SELECT_6 0x15 |
| #define MODE_SENSE_6 0x1A |
| #define START_STOP_UNIT 0x1B |
| #define START_STOP 0x1B |
| #define RESERVE 0x16 |
| #define RELEASE 0x17 |
| #define RECEIVE_DIAGNOSTIC 0x1C |
| #define SEND_DIAGNOSTIC 0x1D |
| #define PREVENT_ALLOW 0x1E |
| #define READ_CAPACITY 0x25 |
| #define READ_10 0x28 |
| #define WRITE_10 0x2A |
| #define POSITION_TO_ELEMENT 0x2B |
| #define WRITE_VERIFY_10 0x2E |
| #define VERIFY_10 0x2F |
| #define SYNCHRONIZE_CACHE 0x35 |
| #define READ_DEFECT_DATA_10 0x37 |
| #define WRITE_BUFFER 0x3B |
| #define READ_BUFFER 0x3C |
| #define CHANGE_DEFINITION 0x40 |
| #define WRITE_SAME_10 0x41 |
| #define UNMAP 0x42 |
| #define LOG_SELECT 0x4C |
| #define LOG_SENSE 0x4D |
| #define MODE_SELECT_10 0x55 |
| #define RESERVE_10 0x56 |
| #define RELEASE_10 0x57 |
| #define MODE_SENSE_10 0x5A |
| #define PERSISTENT_RES_IN 0x5E |
| #define PERSISTENT_RES_OUT 0x5F |
| #define EXTENDED_CDB 0x7E |
| #define VARIABLE_LEN_CDB 0x7F |
| #define EXTENDED_COPY 0x83 |
| #define RECEIVE_COPY_STATUS 0x84 |
| #define ATA_PASS_16 0x85 |
| #define READ_16 0x88 |
| #define COMPARE_AND_WRITE 0x89 |
| #define WRITE_16 0x8A |
| #define READ_ATTRIBUTE 0x8C |
| #define WRITE_ATTRIBUTE 0x8D |
| #define WRITE_VERIFY_16 0x8E |
| #define VERIFY_16 0x8F |
| #define SYNCHRONIZE_CACHE_16 0x91 |
| #define WRITE_SAME_16 0x93 |
| #define READ_BUFFER_16 0x9B |
| #define WRITE_ATOMIC_16 0x9C |
| #define SERVICE_ACTION_IN 0x9E |
| #define REPORT_LUNS 0xA0 |
| #define ATA_PASS_12 0xA1 |
| #define SECURITY_PROTOCOL_IN 0xA2 |
| #define MAINTENANCE_IN 0xA3 |
| #define MAINTENANCE_OUT 0xA4 |
| #define MOVE_MEDIUM 0xA5 |
| #define READ_12 0xA8 |
| #define WRITE_12 0xAA |
| #define WRITE_VERIFY_12 0xAE |
| #define VERIFY_12 0xAF |
| #define SECURITY_PROTOCOL_OUT 0xB5 |
| #define READ_ELEMENT_STATUS 0xB8 |
| #define READ_CD 0xBE |
| |
| /* Maintenance In Service Action Codes */ |
| #define REPORT_IDENTIFYING_INFRMATION 0x05 |
| #define REPORT_TARGET_PORT_GROUPS 0x0A |
| #define REPORT_ALIASES 0x0B |
| #define REPORT_SUPPORTED_OPERATION_CODES 0x0C |
| #define REPORT_SUPPORTED_TASK_MANAGEMENT_FUNCTIONS 0x0D |
| #define REPORT_PRIORITY 0x0E |
| #define REPORT_TIMESTAMP 0x0F |
| #define MANAGEMENT_PROTOCOL_IN 0x10 |
| /* Maintenance Out Service Action Codes */ |
| #define SET_IDENTIFY_INFORMATION 0x06 |
| #define SET_TARGET_PORT_GROUPS 0x0A |
| #define CHANGE_ALIASES 0x0B |
| #define SET_PRIORITY 0x0E |
| #define SET_TIMESTAMP 0x0F |
| #define MANGAEMENT_PROTOCOL_OUT 0x10 |
| |
| /* |
| * Device Types |
| */ |
| #define T_DIRECT 0x00 |
| #define T_SEQUENTIAL 0x01 |
| #define T_PRINTER 0x02 |
| #define T_PROCESSOR 0x03 |
| #define T_WORM 0x04 |
| #define T_CDROM 0x05 |
| #define T_SCANNER 0x06 |
| #define T_OPTICAL 0x07 |
| #define T_CHANGER 0x08 |
| #define T_COMM 0x09 |
| #define T_ASC0 0x0a |
| #define T_ASC1 0x0b |
| #define T_STORARRAY 0x0c |
| #define T_ENCLOSURE 0x0d |
| #define T_RBC 0x0e |
| #define T_OCRW 0x0f |
| #define T_OSD 0x11 |
| #define T_ADC 0x12 |
| #define T_ZBC_HM 0x14 |
| #define T_NODEVICE 0x1f |
| #define T_ANY 0xff /* Used in Quirk table matches */ |
| |
| #define T_REMOV 1 |
| #define T_FIXED 0 |
| |
| /* |
| * This length is the initial inquiry length used by the probe code, as |
| * well as the length necessary for scsi_print_inquiry() to function |
| * correctly. If either use requires a different length in the future, |
| * the two values should be de-coupled. |
| */ |
| #define SHORT_INQUIRY_LENGTH 36 |
| |
| struct scsi_inquiry_data |
| { |
| u_int8_t device; |
| #define SID_TYPE(inq_data) ((inq_data)->device & 0x1f) |
| #define SID_QUAL(inq_data) (((inq_data)->device & 0xE0) >> 5) |
| #define SID_QUAL_LU_CONNECTED 0x00 /* |
| * The specified peripheral device |
| * type is currently connected to |
| * logical unit. If the target cannot |
| * determine whether or not a physical |
| * device is currently connected, it |
| * shall also use this peripheral |
| * qualifier when returning the INQUIRY |
| * data. This peripheral qualifier |
| * does not mean that the device is |
| * ready for access by the initiator. |
| */ |
| #define SID_QUAL_LU_OFFLINE 0x01 /* |
| * The target is capable of supporting |
| * the specified peripheral device type |
| * on this logical unit; however, the |
| * physical device is not currently |
| * connected to this logical unit. |
| */ |
| #define SID_QUAL_RSVD 0x02 |
| #define SID_QUAL_BAD_LU 0x03 /* |
| * The target is not capable of |
| * supporting a physical device on |
| * this logical unit. For this |
| * peripheral qualifier the peripheral |
| * device type shall be set to 1Fh to |
| * provide compatibility with previous |
| * versions of SCSI. All other |
| * peripheral device type values are |
| * reserved for this peripheral |
| * qualifier. |
| */ |
| #define SID_QUAL_IS_VENDOR_UNIQUE(inq_data) ((SID_QUAL(inq_data) & 0x04) != 0) |
| u_int8_t dev_qual2; |
| #define SID_QUAL2 0x7F |
| #define SID_LU_CONG 0x40 |
| #define SID_RMB 0x80 |
| #define SID_IS_REMOVABLE(inq_data) (((inq_data)->dev_qual2 & SID_RMB) != 0) |
| u_int8_t version; |
| #define SID_ANSI_REV(inq_data) ((inq_data)->version & 0x07) |
| #define SCSI_REV_0 0 |
| #define SCSI_REV_CCS 1 |
| #define SCSI_REV_2 2 |
| #define SCSI_REV_SPC 3 |
| #define SCSI_REV_SPC2 4 |
| #define SCSI_REV_SPC3 5 |
| #define SCSI_REV_SPC4 6 |
| |
| #define SID_ECMA 0x38 |
| #define SID_ISO 0xC0 |
| u_int8_t response_format; |
| #define SID_AENC 0x80 |
| #define SID_TrmIOP 0x40 |
| #define SID_NormACA 0x20 |
| #define SID_HiSup 0x10 |
| u_int8_t additional_length; |
| #define SID_ADDITIONAL_LENGTH(iqd) \ |
| ((iqd)->additional_length + \ |
| __offsetof(struct scsi_inquiry_data, additional_length) + 1) |
| u_int8_t spc3_flags; |
| #define SPC3_SID_PROTECT 0x01 |
| #define SPC3_SID_3PC 0x08 |
| #define SPC3_SID_TPGS_MASK 0x30 |
| #define SPC3_SID_TPGS_IMPLICIT 0x10 |
| #define SPC3_SID_TPGS_EXPLICIT 0x20 |
| #define SPC3_SID_ACC 0x40 |
| #define SPC3_SID_SCCS 0x80 |
| u_int8_t spc2_flags; |
| #define SPC2_SID_ADDR16 0x01 |
| #define SPC2_SID_MChngr 0x08 |
| #define SPC2_SID_MultiP 0x10 |
| #define SPC2_SID_EncServ 0x40 |
| #define SPC2_SID_BQueue 0x80 |
| |
| #define INQ_DATA_TQ_ENABLED(iqd) \ |
| ((SID_ANSI_REV(iqd) < SCSI_REV_SPC2)? ((iqd)->flags & SID_CmdQue) : \ |
| (((iqd)->flags & SID_CmdQue) && !((iqd)->spc2_flags & SPC2_SID_BQueue)) || \ |
| (!((iqd)->flags & SID_CmdQue) && ((iqd)->spc2_flags & SPC2_SID_BQueue))) |
| |
| u_int8_t flags; |
| #define SID_SftRe 0x01 |
| #define SID_CmdQue 0x02 |
| #define SID_Linked 0x08 |
| #define SID_Sync 0x10 |
| #define SID_WBus16 0x20 |
| #define SID_WBus32 0x40 |
| #define SID_RelAdr 0x80 |
| #define SID_VENDOR_SIZE 8 |
| char vendor[SID_VENDOR_SIZE]; |
| #define SID_PRODUCT_SIZE 16 |
| char product[SID_PRODUCT_SIZE]; |
| #define SID_REVISION_SIZE 4 |
| char revision[SID_REVISION_SIZE]; |
| /* |
| * The following fields were taken from SCSI Primary Commands - 2 |
| * (SPC-2) Revision 14, Dated 11 November 1999 |
| */ |
| #define SID_VENDOR_SPECIFIC_0_SIZE 20 |
| u_int8_t vendor_specific0[SID_VENDOR_SPECIFIC_0_SIZE]; |
| /* |
| * An extension of SCSI Parallel Specific Values |
| */ |
| #define SID_SPI_IUS 0x01 |
| #define SID_SPI_QAS 0x02 |
| #define SID_SPI_CLOCK_ST 0x00 |
| #define SID_SPI_CLOCK_DT 0x04 |
| #define SID_SPI_CLOCK_DT_ST 0x0C |
| #define SID_SPI_MASK 0x0F |
| u_int8_t spi3data; |
| u_int8_t reserved2; |
| /* |
| * Version Descriptors, stored 2 byte values. |
| */ |
| u_int8_t version1[2]; |
| u_int8_t version2[2]; |
| u_int8_t version3[2]; |
| u_int8_t version4[2]; |
| u_int8_t version5[2]; |
| u_int8_t version6[2]; |
| u_int8_t version7[2]; |
| u_int8_t version8[2]; |
| |
| u_int8_t reserved3[22]; |
| |
| #define SID_VENDOR_SPECIFIC_1_SIZE 160 |
| u_int8_t vendor_specific1[SID_VENDOR_SPECIFIC_1_SIZE]; |
| }; |
| |
| /* |
| * This structure is more suited to initiator operation, because the |
| * maximum number of supported pages is already allocated. |
| */ |
| struct scsi_vpd_supported_page_list |
| { |
| u_int8_t device; |
| u_int8_t page_code; |
| #define SVPD_SUPPORTED_PAGE_LIST 0x00 |
| #define SVPD_SUPPORTED_PAGES_HDR_LEN 4 |
| u_int8_t reserved; |
| u_int8_t length; /* number of VPD entries */ |
| #define SVPD_SUPPORTED_PAGES_SIZE 251 |
| u_int8_t list[SVPD_SUPPORTED_PAGES_SIZE]; |
| }; |
| |
| /* |
| * This structure is more suited to target operation, because the |
| * number of supported pages is left to the user to allocate. |
| */ |
| struct scsi_vpd_supported_pages |
| { |
| u_int8_t device; |
| u_int8_t page_code; |
| u_int8_t reserved; |
| #define SVPD_SUPPORTED_PAGES 0x00 |
| u_int8_t length; |
| u_int8_t page_list[0]; |
| }; |
| |
| |
| struct scsi_vpd_unit_serial_number |
| { |
| u_int8_t device; |
| u_int8_t page_code; |
| #define SVPD_UNIT_SERIAL_NUMBER 0x80 |
| u_int8_t reserved; |
| u_int8_t length; /* serial number length */ |
| #define SVPD_SERIAL_NUM_SIZE 251 |
| u_int8_t serial_num[SVPD_SERIAL_NUM_SIZE]; |
| }; |
| |
| struct scsi_vpd_device_id |
| { |
| u_int8_t device; |
| u_int8_t page_code; |
| #define SVPD_DEVICE_ID 0x83 |
| #define SVPD_DEVICE_ID_MAX_SIZE 252 |
| #define SVPD_DEVICE_ID_HDR_LEN \ |
| __offsetof(struct scsi_vpd_device_id, desc_list) |
| u_int8_t length[2]; |
| u_int8_t desc_list[]; |
| }; |
| |
| struct scsi_vpd_id_descriptor |
| { |
| u_int8_t proto_codeset; |
| /* |
| * See the SCSI_PROTO definitions above for the protocols. |
| */ |
| #define SVPD_ID_PROTO_SHIFT 4 |
| #define SVPD_ID_CODESET_BINARY 0x01 |
| #define SVPD_ID_CODESET_ASCII 0x02 |
| #define SVPD_ID_CODESET_UTF8 0x03 |
| #define SVPD_ID_CODESET_MASK 0x0f |
| u_int8_t id_type; |
| #define SVPD_ID_PIV 0x80 |
| #define SVPD_ID_ASSOC_LUN 0x00 |
| #define SVPD_ID_ASSOC_PORT 0x10 |
| #define SVPD_ID_ASSOC_TARGET 0x20 |
| #define SVPD_ID_ASSOC_MASK 0x30 |
| #define SVPD_ID_TYPE_VENDOR 0x00 |
| #define SVPD_ID_TYPE_T10 0x01 |
| #define SVPD_ID_TYPE_EUI64 0x02 |
| #define SVPD_ID_TYPE_NAA 0x03 |
| #define SVPD_ID_TYPE_RELTARG 0x04 |
| #define SVPD_ID_TYPE_TPORTGRP 0x05 |
| #define SVPD_ID_TYPE_LUNGRP 0x06 |
| #define SVPD_ID_TYPE_MD5_LUN_ID 0x07 |
| #define SVPD_ID_TYPE_SCSI_NAME 0x08 |
| #define SVPD_ID_TYPE_PROTO 0x09 |
| #define SVPD_ID_TYPE_UUID 0x0a |
| #define SVPD_ID_TYPE_MASK 0x0f |
| u_int8_t reserved; |
| u_int8_t length; |
| #define SVPD_DEVICE_ID_DESC_HDR_LEN \ |
| __offsetof(struct scsi_vpd_id_descriptor, identifier) |
| u_int8_t identifier[]; |
| }; |
| |
| struct scsi_vpd_id_t10 |
| { |
| u_int8_t vendor[8]; |
| u_int8_t vendor_spec_id[0]; |
| }; |
| |
| struct scsi_vpd_id_eui64 |
| { |
| u_int8_t ieee_company_id[3]; |
| u_int8_t extension_id[5]; |
| }; |
| |
| struct scsi_vpd_id_naa_basic |
| { |
| uint8_t naa; |
| /* big endian, packed: |
| uint8_t naa : 4; |
| uint8_t naa_desig : 4; |
| */ |
| #define SVPD_ID_NAA_NAA_SHIFT 4 |
| #define SVPD_ID_NAA_IEEE_EXT 0x02 |
| #define SVPD_ID_NAA_LOCAL_REG 0x03 |
| #define SVPD_ID_NAA_IEEE_REG 0x05 |
| #define SVPD_ID_NAA_IEEE_REG_EXT 0x06 |
| uint8_t naa_data[]; |
| }; |
| |
| struct scsi_vpd_id_naa_ieee_extended_id |
| { |
| uint8_t naa; |
| uint8_t vendor_specific_id_a; |
| uint8_t ieee_company_id[3]; |
| uint8_t vendor_specific_id_b[4]; |
| }; |
| |
| struct scsi_vpd_id_naa_local_reg |
| { |
| uint8_t naa; |
| uint8_t local_value[7]; |
| }; |
| |
| struct scsi_vpd_id_naa_ieee_reg |
| { |
| uint8_t naa; |
| uint8_t reg_value[7]; |
| /* big endian, packed: |
| uint8_t naa_basic : 4; |
| uint8_t ieee_company_id_0 : 4; |
| uint8_t ieee_company_id_1[2]; |
| uint8_t ieee_company_id_2 : 4; |
| uint8_t vendor_specific_id_0 : 4; |
| uint8_t vendor_specific_id_1[4]; |
| */ |
| }; |
| |
| struct scsi_vpd_id_naa_ieee_reg_extended |
| { |
| uint8_t naa; |
| uint8_t reg_value[15]; |
| /* big endian, packed: |
| uint8_t naa_basic : 4; |
| uint8_t ieee_company_id_0 : 4; |
| uint8_t ieee_company_id_1[2]; |
| uint8_t ieee_company_id_2 : 4; |
| uint8_t vendor_specific_id_0 : 4; |
| uint8_t vendor_specific_id_1[4]; |
| uint8_t vendor_specific_id_ext[8]; |
| */ |
| }; |
| |
| struct scsi_vpd_id_rel_trgt_port_id |
| { |
| uint8_t obsolete[2]; |
| uint8_t rel_trgt_port_id[2]; |
| }; |
| |
| struct scsi_vpd_id_trgt_port_grp_id |
| { |
| uint8_t reserved[2]; |
| uint8_t trgt_port_grp[2]; |
| }; |
| |
| struct scsi_vpd_id_lun_grp_id |
| { |
| uint8_t reserved[2]; |
| uint8_t log_unit_grp[2]; |
| }; |
| |
| struct scsi_vpd_id_md5_lun_id |
| { |
| uint8_t lun_id[16]; |
| }; |
| |
| struct scsi_vpd_id_scsi_name |
| { |
| uint8_t name_string[256]; |
| }; |
| |
| struct scsi_service_action_in |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| uint8_t action_dependent[13]; |
| uint8_t control; |
| }; |
| |
| struct scsi_vpd_extended_inquiry_data |
| { |
| uint8_t device; |
| uint8_t page_code; |
| #define SVPD_EXTENDED_INQUIRY_DATA 0x86 |
| uint8_t page_length[2]; |
| uint8_t flags1; |
| |
| /* These values are for direct access devices */ |
| #define SVPD_EID_AM_MASK 0xC0 |
| #define SVPD_EID_AM_DEFER 0x80 |
| #define SVPD_EID_AM_IMMED 0x40 |
| #define SVPD_EID_AM_UNDEFINED 0x00 |
| #define SVPD_EID_AM_RESERVED 0xc0 |
| #define SVPD_EID_SPT 0x38 |
| #define SVPD_EID_SPT_1 0x00 |
| #define SVPD_EID_SPT_12 0x08 |
| #define SVPD_EID_SPT_2 0x10 |
| #define SVPD_EID_SPT_13 0x18 |
| #define SVPD_EID_SPT_3 0x20 |
| #define SVPD_EID_SPT_23 0x28 |
| #define SVPD_EID_SPT_123 0x38 |
| |
| /* These values are for sequential access devices */ |
| #define SVPD_EID_SA_SPT_LBP 0x08 |
| |
| #define SVPD_EID_GRD_CHK 0x04 |
| #define SVPD_EID_APP_CHK 0x02 |
| #define SVPD_EID_REF_CHK 0x01 |
| |
| uint8_t flags2; |
| #define SVPD_EID_UASK_SUP 0x20 |
| #define SVPD_EID_GROUP_SUP 0x10 |
| #define SVPD_EID_PRIOR_SUP 0x08 |
| #define SVPD_EID_HEADSUP 0x04 |
| #define SVPD_EID_ORDSUP 0x02 |
| #define SVPD_EID_SIMPSUP 0x01 |
| uint8_t flags3; |
| #define SVPD_EID_WU_SUP 0x08 |
| #define SVPD_EID_CRD_SUP 0x04 |
| #define SVPD_EID_NV_SUP 0x02 |
| #define SVPD_EID_V_SUP 0x01 |
| uint8_t flags4; |
| #define SVPD_EID_P_I_I_SUP 0x10 |
| #define SVPD_EID_LUICLT 0x01 |
| uint8_t flags5; |
| #define SVPD_EID_R_SUP 0x10 |
| #define SVPD_EID_CBCS 0x01 |
| uint8_t flags6; |
| #define SVPD_EID_MULTI_I_T_FW 0x0F |
| #define SVPD_EID_MC_VENDOR_SPEC 0x00 |
| #define SVPD_EID_MC_MODE_1 0x01 |
| #define SVPD_EID_MC_MODE_2 0x02 |
| #define SVPD_EID_MC_MODE_3 0x03 |
| uint8_t est[2]; |
| uint8_t flags7; |
| #define SVPD_EID_POA_SUP 0x80 |
| #define SVPD_EID_HRA_SUP 0x80 |
| #define SVPD_EID_VSA_SUP 0x80 |
| uint8_t max_sense_length; |
| uint8_t reserved2[50]; |
| }; |
| |
| struct scsi_vpd_mode_page_policy_descr |
| { |
| uint8_t page_code; |
| uint8_t subpage_code; |
| uint8_t policy; |
| #define SVPD_MPP_SHARED 0x00 |
| #define SVPD_MPP_PORT 0x01 |
| #define SVPD_MPP_I_T 0x03 |
| #define SVPD_MPP_MLUS 0x80 |
| uint8_t reserved; |
| }; |
| |
| struct scsi_vpd_mode_page_policy |
| { |
| uint8_t device; |
| uint8_t page_code; |
| #define SVPD_MODE_PAGE_POLICY 0x87 |
| uint8_t page_length[2]; |
| struct scsi_vpd_mode_page_policy_descr descr[0]; |
| }; |
| |
| struct scsi_diag_page { |
| uint8_t page_code; |
| uint8_t page_specific_flags; |
| uint8_t length[2]; |
| uint8_t params[0]; |
| }; |
| |
| struct scsi_vpd_port_designation |
| { |
| uint8_t reserved[2]; |
| uint8_t relative_port_id[2]; |
| uint8_t reserved2[2]; |
| uint8_t initiator_transportid_length[2]; |
| uint8_t initiator_transportid[0]; |
| }; |
| |
| struct scsi_vpd_port_designation_cont |
| { |
| uint8_t reserved[2]; |
| uint8_t target_port_descriptors_length[2]; |
| struct scsi_vpd_id_descriptor target_port_descriptors[0]; |
| }; |
| |
| struct scsi_vpd_scsi_ports |
| { |
| u_int8_t device; |
| u_int8_t page_code; |
| #define SVPD_SCSI_PORTS 0x88 |
| u_int8_t page_length[2]; |
| struct scsi_vpd_port_designation design[]; |
| }; |
| |
| /* |
| * ATA Information VPD Page based on |
| * T10/2126-D Revision 04 |
| */ |
| #define SVPD_ATA_INFORMATION 0x89 |
| |
| |
| struct scsi_vpd_tpc_descriptor |
| { |
| uint8_t desc_type[2]; |
| uint8_t desc_length[2]; |
| uint8_t parameters[]; |
| }; |
| |
| struct scsi_vpd_tpc_descriptor_bdrl |
| { |
| uint8_t desc_type[2]; |
| #define SVPD_TPC_BDRL 0x0000 |
| uint8_t desc_length[2]; |
| uint8_t vendor_specific[6]; |
| uint8_t maximum_ranges[2]; |
| uint8_t maximum_inactivity_timeout[4]; |
| uint8_t default_inactivity_timeout[4]; |
| uint8_t maximum_token_transfer_size[8]; |
| uint8_t optimal_transfer_count[8]; |
| }; |
| |
| struct scsi_vpd_tpc_descriptor_sc_descr |
| { |
| uint8_t opcode; |
| uint8_t sa_length; |
| uint8_t supported_service_actions[0]; |
| }; |
| |
| struct scsi_vpd_tpc_descriptor_sc |
| { |
| uint8_t desc_type[2]; |
| #define SVPD_TPC_SC 0x0001 |
| uint8_t desc_length[2]; |
| uint8_t list_length; |
| struct scsi_vpd_tpc_descriptor_sc_descr descr[]; |
| }; |
| |
| struct scsi_vpd_tpc_descriptor_pd |
| { |
| uint8_t desc_type[2]; |
| #define SVPD_TPC_PD 0x0004 |
| uint8_t desc_length[2]; |
| uint8_t reserved[4]; |
| uint8_t maximum_cscd_descriptor_count[2]; |
| uint8_t maximum_segment_descriptor_count[2]; |
| uint8_t maximum_descriptor_list_length[4]; |
| uint8_t maximum_inline_data_length[4]; |
| uint8_t reserved2[12]; |
| }; |
| |
| struct scsi_vpd_tpc_descriptor_sd |
| { |
| uint8_t desc_type[2]; |
| #define SVPD_TPC_SD 0x0008 |
| uint8_t desc_length[2]; |
| uint8_t list_length; |
| uint8_t supported_descriptor_codes[]; |
| }; |
| |
| struct scsi_vpd_tpc_descriptor_sdid |
| { |
| uint8_t desc_type[2]; |
| #define SVPD_TPC_SDID 0x000C |
| uint8_t desc_length[2]; |
| uint8_t list_length[2]; |
| uint8_t supported_descriptor_ids[]; |
| }; |
| |
| struct scsi_vpd_tpc_descriptor_rtf_block |
| { |
| uint8_t type_format; |
| #define SVPD_TPC_RTF_BLOCK 0x00 |
| uint8_t reserved; |
| uint8_t desc_length[2]; |
| uint8_t reserved2[2]; |
| uint8_t optimal_length_granularity[2]; |
| uint8_t maximum_bytes[8]; |
| uint8_t optimal_bytes[8]; |
| uint8_t optimal_bytes_to_token_per_segment[8]; |
| uint8_t optimal_bytes_from_token_per_segment[8]; |
| uint8_t reserved3[8]; |
| }; |
| |
| struct scsi_vpd_tpc_descriptor_rtf |
| { |
| uint8_t desc_type[2]; |
| #define SVPD_TPC_RTF 0x0106 |
| uint8_t desc_length[2]; |
| uint8_t remote_tokens; |
| uint8_t reserved[11]; |
| uint8_t minimum_token_lifetime[4]; |
| uint8_t maximum_token_lifetime[4]; |
| uint8_t maximum_token_inactivity_timeout[4]; |
| uint8_t reserved2[18]; |
| uint8_t type_specific_features_length[2]; |
| uint8_t type_specific_features[0]; |
| }; |
| |
| struct scsi_vpd_tpc_descriptor_srtd |
| { |
| uint8_t rod_type[4]; |
| uint8_t flags; |
| #define SVPD_TPC_SRTD_TOUT 0x01 |
| #define SVPD_TPC_SRTD_TIN 0x02 |
| #define SVPD_TPC_SRTD_ECPY 0x80 |
| uint8_t reserved; |
| uint8_t preference_indicator[2]; |
| uint8_t reserved2[56]; |
| }; |
| |
| struct scsi_vpd_tpc_descriptor_srt |
| { |
| uint8_t desc_type[2]; |
| #define SVPD_TPC_SRT 0x0108 |
| uint8_t desc_length[2]; |
| uint8_t reserved[2]; |
| uint8_t rod_type_descriptors_length[2]; |
| uint8_t rod_type_descriptors[0]; |
| }; |
| |
| struct scsi_vpd_tpc_descriptor_gco |
| { |
| uint8_t desc_type[2]; |
| #define SVPD_TPC_GCO 0x8001 |
| uint8_t desc_length[2]; |
| uint8_t total_concurrent_copies[4]; |
| uint8_t maximum_identified_concurrent_copies[4]; |
| uint8_t maximum_segment_length[4]; |
| uint8_t data_segment_granularity; |
| uint8_t inline_data_granularity; |
| uint8_t reserved[18]; |
| }; |
| |
| struct scsi_vpd_tpc |
| { |
| uint8_t device; |
| uint8_t page_code; |
| #define SVPD_SCSI_TPC 0x8F |
| uint8_t page_length[2]; |
| struct scsi_vpd_tpc_descriptor descr[]; |
| }; |
| |
| /* |
| * Block Device Characteristics VPD Page based on |
| * T10/1799-D Revision 31 |
| */ |
| struct scsi_vpd_block_characteristics |
| { |
| u_int8_t device; |
| u_int8_t page_code; |
| #define SVPD_BDC 0xB1 |
| u_int8_t page_length[2]; |
| u_int8_t medium_rotation_rate[2]; |
| #define SVPD_BDC_RATE_NOT_REPORTED 0x00 |
| #define SVPD_BDC_RATE_NON_ROTATING 0x01 |
| u_int8_t reserved1; |
| u_int8_t nominal_form_factor; |
| #define SVPD_BDC_FORM_NOT_REPORTED 0x00 |
| #define SVPD_BDC_FORM_5_25INCH 0x01 |
| #define SVPD_BDC_FORM_3_5INCH 0x02 |
| #define SVPD_BDC_FORM_2_5INCH 0x03 |
| #define SVPD_BDC_FORM_1_5INCH 0x04 |
| #define SVPD_BDC_FORM_LESSTHAN_1_5INCH 0x05 |
| u_int8_t reserved2[56]; |
| }; |
| |
| /* |
| * Block Device Characteristics VPD Page |
| */ |
| struct scsi_vpd_block_device_characteristics |
| { |
| uint8_t device; |
| uint8_t page_code; |
| #define SVPD_BDC 0xB1 |
| uint8_t page_length[2]; |
| uint8_t medium_rotation_rate[2]; |
| #define SVPD_NOT_REPORTED 0x0000 |
| #define SVPD_NON_ROTATING 0x0001 |
| uint8_t product_type; |
| uint8_t wab_wac_ff; |
| uint8_t flags; |
| #define SVPD_VBULS 0x01 |
| #define SVPD_FUAB 0x02 |
| #define SVPD_ZBC_NR 0x00 /* Not Reported */ |
| #define SVPD_HAW_ZBC 0x10 /* Host Aware */ |
| #define SVPD_DM_ZBC 0x20 /* Drive Managed */ |
| #define SVPD_ZBC_MASK 0x30 /* Zoned mask */ |
| uint8_t reserved[55]; |
| }; |
| |
| #define SBDC_IS_PRESENT(bdc, length, field) \ |
| ((length >= offsetof(struct scsi_vpd_block_device_characteristics, \ |
| field) + sizeof(bdc->field)) ? 1 : 0) |
| |
| /* |
| * Logical Block Provisioning VPD Page based on |
| * T10/1799-D Revision 31 |
| */ |
| struct scsi_vpd_logical_block_prov |
| { |
| u_int8_t device; |
| u_int8_t page_code; |
| #define SVPD_LBP 0xB2 |
| u_int8_t page_length[2]; |
| #define SVPD_LBP_PL_BASIC 0x04 |
| u_int8_t threshold_exponent; |
| u_int8_t flags; |
| #define SVPD_LBP_UNMAP 0x80 |
| #define SVPD_LBP_WS16 0x40 |
| #define SVPD_LBP_WS10 0x20 |
| #define SVPD_LBP_RZ 0x04 |
| #define SVPD_LBP_ANC_SUP 0x02 |
| #define SVPD_LBP_DP 0x01 |
| u_int8_t prov_type; |
| #define SVPD_LBP_RESOURCE 0x01 |
| #define SVPD_LBP_THIN 0x02 |
| u_int8_t reserved; |
| /* |
| * Provisioning Group Descriptor can be here if SVPD_LBP_DP is set |
| * Its size can be determined from page_length - 4 |
| */ |
| }; |
| |
| /* |
| * Block Limits VDP Page based on SBC-4 Revision 2 |
| */ |
| struct scsi_vpd_block_limits |
| { |
| u_int8_t device; |
| u_int8_t page_code; |
| #define SVPD_BLOCK_LIMITS 0xB0 |
| u_int8_t page_length[2]; |
| #define SVPD_BL_PL_BASIC 0x10 |
| #define SVPD_BL_PL_TP 0x3C |
| u_int8_t reserved1; |
| u_int8_t max_cmp_write_len; |
| u_int8_t opt_txfer_len_grain[2]; |
| u_int8_t max_txfer_len[4]; |
| u_int8_t opt_txfer_len[4]; |
| u_int8_t max_prefetch[4]; |
| u_int8_t max_unmap_lba_cnt[4]; |
| u_int8_t max_unmap_blk_cnt[4]; |
| u_int8_t opt_unmap_grain[4]; |
| u_int8_t unmap_grain_align[4]; |
| u_int8_t max_write_same_length[8]; |
| u_int8_t max_atomic_transfer_length[4]; |
| u_int8_t atomic_alignment[4]; |
| u_int8_t atomic_transfer_length_granularity[4]; |
| u_int8_t max_atomic_transfer_length_with_atomic_boundary[4]; |
| u_int8_t max_atomic_boundary_size[4]; |
| }; |
| |
| /* |
| * Zoned Block Device Characacteristics VPD page. |
| * From ZBC-r04, dated August 12, 2015. |
| */ |
| struct scsi_vpd_zoned_bdc { |
| uint8_t device; |
| uint8_t page_code; |
| #define SVPD_ZONED_BDC 0xB6 |
| uint8_t page_length[2]; |
| #define SVPD_ZBDC_PL 0x3C |
| uint8_t flags; |
| #define SVPD_ZBDC_URSWRZ 0x01 |
| uint8_t reserved1[3]; |
| uint8_t optimal_seq_zones[4]; |
| #define SVPD_ZBDC_OPT_SEQ_NR 0xffffffff |
| uint8_t optimal_nonseq_zones[4]; |
| #define SVPD_ZBDC_OPT_NONSEQ_NR 0xffffffff |
| uint8_t max_seq_req_zones[4]; |
| #define SVPD_ZBDC_MAX_SEQ_UNLIMITED 0xffffffff |
| uint8_t reserved2[44]; |
| }; |
| |
| struct scsi_read_capacity |
| { |
| u_int8_t opcode; |
| u_int8_t byte2; |
| #define SRC_RELADR 0x01 |
| u_int8_t addr[4]; |
| u_int8_t unused[2]; |
| u_int8_t pmi; |
| #define SRC_PMI 0x01 |
| u_int8_t control; |
| }; |
| |
| struct scsi_read_capacity_16 |
| { |
| uint8_t opcode; |
| #define SRC16_SERVICE_ACTION 0x10 |
| uint8_t service_action; |
| uint8_t addr[8]; |
| uint8_t alloc_len[4]; |
| #define SRC16_PMI 0x01 |
| #define SRC16_RELADR 0x02 |
| uint8_t reladr; |
| uint8_t control; |
| }; |
| |
| struct scsi_read_capacity_data |
| { |
| u_int8_t addr[4]; |
| u_int8_t length[4]; |
| }; |
| |
| struct scsi_read_capacity_data_long |
| { |
| uint8_t addr[8]; |
| uint8_t length[4]; |
| #define SRC16_PROT_EN 0x01 |
| #define SRC16_P_TYPE 0x0e |
| #define SRC16_PTYPE_1 0x00 |
| #define SRC16_PTYPE_2 0x02 |
| #define SRC16_PTYPE_3 0x04 |
| uint8_t prot; |
| #define SRC16_LBPPBE 0x0f |
| #define SRC16_PI_EXPONENT 0xf0 |
| #define SRC16_PI_EXPONENT_SHIFT 4 |
| uint8_t prot_lbppbe; |
| #define SRC16_LALBA 0x3f |
| #define SRC16_LBPRZ 0x40 |
| #define SRC16_LBPME 0x80 |
| /* |
| * Alternate versions of these macros that are intended for use on a 16-bit |
| * version of the lalba_lbp field instead of the array of 2 8 bit numbers. |
| */ |
| #define SRC16_LALBA_A 0x3fff |
| #define SRC16_LBPRZ_A 0x4000 |
| #define SRC16_LBPME_A 0x8000 |
| uint8_t lalba_lbp[2]; |
| uint8_t reserved[16]; |
| }; |
| |
| struct scsi_get_lba_status |
| { |
| uint8_t opcode; |
| #define SGLS_SERVICE_ACTION 0x12 |
| uint8_t service_action; |
| uint8_t addr[8]; |
| uint8_t alloc_len[4]; |
| uint8_t reserved; |
| uint8_t control; |
| }; |
| |
| struct scsi_get_lba_status_data_descr |
| { |
| uint8_t addr[8]; |
| uint8_t length[4]; |
| uint8_t status; |
| uint8_t reserved[3]; |
| }; |
| |
| struct scsi_get_lba_status_data |
| { |
| uint8_t length[4]; |
| uint8_t reserved[4]; |
| struct scsi_get_lba_status_data_descr descr[]; |
| }; |
| |
| struct scsi_report_luns |
| { |
| uint8_t opcode; |
| uint8_t reserved1; |
| #define RPL_REPORT_DEFAULT 0x00 |
| #define RPL_REPORT_WELLKNOWN 0x01 |
| #define RPL_REPORT_ALL 0x02 |
| #define RPL_REPORT_ADMIN 0x10 |
| #define RPL_REPORT_NONSUBSID 0x11 |
| #define RPL_REPORT_CONGLOM 0x12 |
| uint8_t select_report; |
| uint8_t reserved2[3]; |
| uint8_t length[4]; |
| uint8_t reserved3; |
| uint8_t control; |
| }; |
| |
| struct scsi_report_luns_lundata { |
| uint8_t lundata[8]; |
| #define RPL_LUNDATA_PERIPH_BUS_MASK 0x3f |
| #define RPL_LUNDATA_FLAT_LUN_MASK 0x3f |
| #define RPL_LUNDATA_FLAT_LUN_BITS 0x06 |
| #define RPL_LUNDATA_LUN_TARG_MASK 0x3f |
| #define RPL_LUNDATA_LUN_BUS_MASK 0xe0 |
| #define RPL_LUNDATA_LUN_LUN_MASK 0x1f |
| #define RPL_LUNDATA_EXT_LEN_MASK 0x30 |
| #define RPL_LUNDATA_EXT_EAM_MASK 0x0f |
| #define RPL_LUNDATA_EXT_EAM_WK 0x01 |
| #define RPL_LUNDATA_EXT_EAM_NOT_SPEC 0x0f |
| #define RPL_LUNDATA_ATYP_MASK 0xc0 /* MBZ for type 0 lun */ |
| #define RPL_LUNDATA_ATYP_PERIPH 0x00 |
| #define RPL_LUNDATA_ATYP_FLAT 0x40 |
| #define RPL_LUNDATA_ATYP_LUN 0x80 |
| #define RPL_LUNDATA_ATYP_EXTLUN 0xc0 |
| }; |
| |
| struct scsi_report_luns_data { |
| u_int8_t length[4]; /* length of LUN inventory, in bytes */ |
| u_int8_t reserved[4]; /* unused */ |
| /* |
| * LUN inventory- we only support the type zero form for now. |
| */ |
| struct scsi_report_luns_lundata luns[0]; |
| }; |
| |
| struct scsi_target_group |
| { |
| uint8_t opcode; |
| uint8_t service_action; |
| #define STG_PDF_MASK 0xe0 |
| #define STG_PDF_LENGTH 0x00 |
| #define STG_PDF_EXTENDED 0x20 |
| uint8_t reserved1[4]; |
| uint8_t length[4]; |
| uint8_t reserved2; |
| uint8_t control; |
| }; |
| |
| struct scsi_target_port_descriptor { |
| uint8_t reserved[2]; |
| uint8_t relative_target_port_identifier[2]; |
| uint8_t desc_list[]; |
| }; |
| |
| struct scsi_target_port_group_descriptor { |
| uint8_t pref_state; |
| #define TPG_PRIMARY 0x80 |
| #define TPG_ASYMMETRIC_ACCESS_STATE_MASK 0xf |
| #define TPG_ASYMMETRIC_ACCESS_OPTIMIZED 0x0 |
| #define TPG_ASYMMETRIC_ACCESS_NONOPTIMIZED 0x1 |
| #define TPG_ASYMMETRIC_ACCESS_STANDBY 0x2 |
| #define TPG_ASYMMETRIC_ACCESS_UNAVAILABLE 0x3 |
| #define TPG_ASYMMETRIC_ACCESS_LBA_DEPENDENT 0x4 |
| #define TPG_ASYMMETRIC_ACCESS_OFFLINE 0xE |
| #define TPG_ASYMMETRIC_ACCESS_TRANSITIONING 0xF |
| uint8_t support; |
| #define TPG_AO_SUP 0x01 |
| #define TPG_AN_SUP 0x02 |
| #define TPG_S_SUP 0x04 |
| #define TPG_U_SUP 0x08 |
| #define TPG_LBD_SUP 0x10 |
| #define TPG_O_SUP 0x40 |
| #define TPG_T_SUP 0x80 |
| uint8_t target_port_group[2]; |
| uint8_t reserved; |
| uint8_t status; |
| #define TPG_UNAVLBL 0 |
| #define TPG_SET_BY_STPG 0x01 |
| #define TPG_IMPLICIT 0x02 |
| uint8_t vendor_specific; |
| uint8_t target_port_count; |
| struct scsi_target_port_descriptor descriptors[]; |
| }; |
| |
| struct scsi_target_group_data { |
| uint8_t length[4]; /* length of returned data, in bytes */ |
| struct scsi_target_port_group_descriptor groups[]; |
| }; |
| |
| struct scsi_target_group_data_extended { |
| uint8_t length[4]; /* length of returned data, in bytes */ |
| uint8_t format_type; /* STG_PDF_LENGTH or STG_PDF_EXTENDED */ |
| uint8_t implicit_transition_time; |
| uint8_t reserved[2]; |
| struct scsi_target_port_group_descriptor groups[]; |
| }; |
| |
| struct scsi_security_protocol_in |
| { |
| uint8_t opcode; |
| uint8_t security_protocol; |
| #define SPI_PROT_INFORMATION 0x00 |
| #define SPI_PROT_CBCS 0x07 |
| #define SPI_PROT_TAPE_DATA_ENC 0x20 |
| #define SPI_PROT_DATA_ENC_CONFIG 0x21 |
| #define SPI_PROT_SA_CREATE_CAP 0x40 |
| #define SPI_PROT_IKEV2_SCSI 0x41 |
| #define SPI_PROT_JEDEC_UFS 0xEC |
| #define SPI_PROT_SDCARD_TFSSS 0xED |
| #define SPI_PROT_AUTH_HOST_TRANSIENT 0xEE |
| #define SPI_PROT_ATA_DEVICE_PASSWORD 0xEF |
| uint8_t security_protocol_specific[2]; |
| uint8_t byte4; |
| #define SPI_INC_512 0x80 |
| uint8_t reserved1; |
| uint8_t length[4]; |
| uint8_t reserved2; |
| uint8_t control; |
| }; |
| |
| struct scsi_security_protocol_out |
| { |
| uint8_t opcode; |
| uint8_t security_protocol; |
| uint8_t security_protocol_specific[2]; |
| uint8_t byte4; |
| #define SPO_INC_512 0x80 |
| uint8_t reserved1; |
| uint8_t length[4]; |
| uint8_t reserved2; |
| uint8_t control; |
| }; |
| |
| typedef enum { |
| SSD_TYPE_NONE, |
| SSD_TYPE_FIXED, |
| SSD_TYPE_DESC |
| } scsi_sense_data_type; |
| |
| typedef enum { |
| SSD_ELEM_NONE, |
| SSD_ELEM_SKIP, |
| SSD_ELEM_DESC, |
| SSD_ELEM_SKS, |
| SSD_ELEM_COMMAND, |
| SSD_ELEM_INFO, |
| SSD_ELEM_FRU, |
| SSD_ELEM_STREAM, |
| SSD_ELEM_MAX |
| } scsi_sense_elem_type; |
| |
| |
| struct scsi_sense_data |
| { |
| uint8_t error_code; |
| /* |
| * SPC-4 says that the maximum length of sense data is 252 bytes. |
| * So this structure is exactly 252 bytes log. |
| */ |
| #define SSD_FULL_SIZE 252 |
| uint8_t sense_buf[SSD_FULL_SIZE - 1]; |
| /* |
| * XXX KDM is this still a reasonable minimum size? |
| */ |
| #define SSD_MIN_SIZE 18 |
| /* |
| * Maximum value for the extra_len field in the sense data. |
| */ |
| #define SSD_EXTRA_MAX 244 |
| }; |
| |
| /* |
| * Fixed format sense data. |
| */ |
| struct scsi_sense_data_fixed |
| { |
| u_int8_t error_code; |
| #define SSD_ERRCODE 0x7F |
| #define SSD_CURRENT_ERROR 0x70 |
| #define SSD_DEFERRED_ERROR 0x71 |
| #define SSD_ERRCODE_VALID 0x80 |
| u_int8_t segment; |
| u_int8_t flags; |
| #define SSD_KEY 0x0F |
| #define SSD_KEY_NO_SENSE 0x00 |
| #define SSD_KEY_RECOVERED_ERROR 0x01 |
| #define SSD_KEY_NOT_READY 0x02 |
| #define SSD_KEY_MEDIUM_ERROR 0x03 |
| #define SSD_KEY_HARDWARE_ERROR 0x04 |
| #define SSD_KEY_ILLEGAL_REQUEST 0x05 |
| #define SSD_KEY_UNIT_ATTENTION 0x06 |
| #define SSD_KEY_DATA_PROTECT 0x07 |
| #define SSD_KEY_BLANK_CHECK 0x08 |
| #define SSD_KEY_Vendor_Specific 0x09 |
| #define SSD_KEY_COPY_ABORTED 0x0a |
| #define SSD_KEY_ABORTED_COMMAND 0x0b |
| #define SSD_KEY_EQUAL 0x0c |
| #define SSD_KEY_VOLUME_OVERFLOW 0x0d |
| #define SSD_KEY_MISCOMPARE 0x0e |
| #define SSD_KEY_COMPLETED 0x0f |
| #define SSD_ILI 0x20 |
| #define SSD_EOM 0x40 |
| #define SSD_FILEMARK 0x80 |
| u_int8_t info[4]; |
| u_int8_t extra_len; |
| u_int8_t cmd_spec_info[4]; |
| u_int8_t add_sense_code; |
| u_int8_t add_sense_code_qual; |
| u_int8_t fru; |
| u_int8_t sense_key_spec[3]; |
| #define SSD_SCS_VALID 0x80 |
| #define SSD_FIELDPTR_CMD 0x40 |
| #define SSD_BITPTR_VALID 0x08 |
| #define SSD_BITPTR_VALUE 0x07 |
| u_int8_t extra_bytes[14]; |
| #define SSD_FIXED_IS_PRESENT(sense, length, field) \ |
| ((length >= (offsetof(struct scsi_sense_data_fixed, field) + \ |
| sizeof(sense->field))) ? 1 :0) |
| #define SSD_FIXED_IS_FILLED(sense, field) \ |
| ((((offsetof(struct scsi_sense_data_fixed, field) + \ |
| sizeof(sense->field)) - \ |
| (offsetof(struct scsi_sense_data_fixed, extra_len) + \ |
| sizeof(sense->extra_len))) <= sense->extra_len) ? 1 : 0) |
| }; |
| |
| /* |
| * Descriptor format sense data definitions. |
| * Introduced in SPC-3. |
| */ |
| struct scsi_sense_data_desc |
| { |
| uint8_t error_code; |
| #define SSD_DESC_CURRENT_ERROR 0x72 |
| #define SSD_DESC_DEFERRED_ERROR 0x73 |
| uint8_t sense_key; |
| uint8_t add_sense_code; |
| uint8_t add_sense_code_qual; |
| uint8_t reserved[3]; |
| /* |
| * Note that SPC-4, section 4.5.2.1 says that the extra_len field |
| * must be less than or equal to 244. |
| */ |
| uint8_t extra_len; |
| uint8_t sense_desc[0]; |
| #define SSD_DESC_IS_PRESENT(sense, length, field) \ |
| ((length >= (offsetof(struct scsi_sense_data_desc, field) + \ |
| sizeof(sense->field))) ? 1 :0) |
| }; |
| |
| struct scsi_sense_desc_header |
| { |
| uint8_t desc_type; |
| uint8_t length; |
| }; |
| /* |
| * The information provide in the Information descriptor is device type or |
| * command specific information, and defined in a command standard. |
| * |
| * Note that any changes to the field names or positions in this structure, |
| * even reserved fields, should be accompanied by an examination of the |
| * code in ctl_set_sense() that uses them. |
| * |
| * Maximum descriptors allowed: 1 (as of SPC-4) |
| */ |
| struct scsi_sense_info |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_INFO 0x00 |
| uint8_t length; |
| uint8_t byte2; |
| #define SSD_INFO_VALID 0x80 |
| uint8_t reserved; |
| uint8_t info[8]; |
| }; |
| |
| /* |
| * Command-specific information depends on the command for which the |
| * reported condition occurred. |
| * |
| * Note that any changes to the field names or positions in this structure, |
| * even reserved fields, should be accompanied by an examination of the |
| * code in ctl_set_sense() that uses them. |
| * |
| * Maximum descriptors allowed: 1 (as of SPC-4) |
| */ |
| struct scsi_sense_command |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_COMMAND 0x01 |
| uint8_t length; |
| uint8_t reserved[2]; |
| uint8_t command_info[8]; |
| }; |
| |
| /* |
| * Sense key specific descriptor. The sense key specific data format |
| * depends on the sense key in question. |
| * |
| * Maximum descriptors allowed: 1 (as of SPC-4) |
| */ |
| struct scsi_sense_sks |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_SKS 0x02 |
| uint8_t length; |
| uint8_t reserved1[2]; |
| uint8_t sense_key_spec[3]; |
| #define SSD_SKS_VALID 0x80 |
| uint8_t reserved2; |
| }; |
| |
| /* |
| * This is used for the Illegal Request sense key (0x05) only. |
| */ |
| struct scsi_sense_sks_field |
| { |
| uint8_t byte0; |
| #define SSD_SKS_FIELD_VALID 0x80 |
| #define SSD_SKS_FIELD_CMD 0x40 |
| #define SSD_SKS_BPV 0x08 |
| #define SSD_SKS_BIT_VALUE 0x07 |
| uint8_t field[2]; |
| }; |
| |
| |
| /* |
| * This is used for the Hardware Error (0x04), Medium Error (0x03) and |
| * Recovered Error (0x01) sense keys. |
| */ |
| struct scsi_sense_sks_retry |
| { |
| uint8_t byte0; |
| #define SSD_SKS_RETRY_VALID 0x80 |
| uint8_t actual_retry_count[2]; |
| }; |
| |
| /* |
| * Used with the NO Sense (0x00) or Not Ready (0x02) sense keys. |
| */ |
| struct scsi_sense_sks_progress |
| { |
| uint8_t byte0; |
| #define SSD_SKS_PROGRESS_VALID 0x80 |
| uint8_t progress[2]; |
| #define SSD_SKS_PROGRESS_DENOM 0x10000 |
| }; |
| |
| /* |
| * Used with the Copy Aborted (0x0a) sense key. |
| */ |
| struct scsi_sense_sks_segment |
| { |
| uint8_t byte0; |
| #define SSD_SKS_SEGMENT_VALID 0x80 |
| #define SSD_SKS_SEGMENT_SD 0x20 |
| #define SSD_SKS_SEGMENT_BPV 0x08 |
| #define SSD_SKS_SEGMENT_BITPTR 0x07 |
| uint8_t field[2]; |
| }; |
| |
| /* |
| * Used with the Unit Attention (0x06) sense key. |
| * |
| * This is currently used to indicate that the unit attention condition |
| * queue has overflowed (when the overflow bit is set). |
| */ |
| struct scsi_sense_sks_overflow |
| { |
| uint8_t byte0; |
| #define SSD_SKS_OVERFLOW_VALID 0x80 |
| #define SSD_SKS_OVERFLOW_SET 0x01 |
| uint8_t reserved[2]; |
| }; |
| |
| /* |
| * This specifies which component is associated with the sense data. There |
| * is no standard meaning for the fru value. |
| * |
| * Maximum descriptors allowed: 1 (as of SPC-4) |
| */ |
| struct scsi_sense_fru |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_FRU 0x03 |
| uint8_t length; |
| uint8_t reserved; |
| uint8_t fru; |
| }; |
| |
| /* |
| * Used for Stream commands, defined in SSC-4. |
| * |
| * Maximum descriptors allowed: 1 (as of SPC-4) |
| */ |
| |
| struct scsi_sense_stream |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_STREAM 0x04 |
| uint8_t length; |
| uint8_t reserved; |
| uint8_t byte3; |
| #define SSD_DESC_STREAM_FM 0x80 |
| #define SSD_DESC_STREAM_EOM 0x40 |
| #define SSD_DESC_STREAM_ILI 0x20 |
| }; |
| |
| /* |
| * Used for Block commands, defined in SBC-3. |
| * |
| * This is currently (as of SBC-3) only used for the Incorrect Length |
| * Indication (ILI) bit, which says that the data length requested in the |
| * READ LONG or WRITE LONG command did not match the length of the logical |
| * block. |
| * |
| * Maximum descriptors allowed: 1 (as of SPC-4) |
| */ |
| struct scsi_sense_block |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_BLOCK 0x05 |
| uint8_t length; |
| uint8_t reserved; |
| uint8_t byte3; |
| #define SSD_DESC_BLOCK_ILI 0x20 |
| }; |
| |
| /* |
| * Used for Object-Based Storage Devices (OSD-3). |
| * |
| * Maximum descriptors allowed: 1 (as of SPC-4) |
| */ |
| struct scsi_sense_osd_objid |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_OSD_OBJID 0x06 |
| uint8_t length; |
| uint8_t reserved[6]; |
| /* |
| * XXX KDM provide the bit definitions here? There are a lot of |
| * them, and we don't have an OSD driver yet. |
| */ |
| uint8_t not_init_cmds[4]; |
| uint8_t completed_cmds[4]; |
| uint8_t partition_id[8]; |
| uint8_t object_id[8]; |
| }; |
| |
| /* |
| * Used for Object-Based Storage Devices (OSD-3). |
| * |
| * Maximum descriptors allowed: 1 (as of SPC-4) |
| */ |
| struct scsi_sense_osd_integrity |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_OSD_INTEGRITY 0x07 |
| uint8_t length; |
| uint8_t integ_check_val[32]; |
| }; |
| |
| /* |
| * Used for Object-Based Storage Devices (OSD-3). |
| * |
| * Maximum descriptors allowed: 1 (as of SPC-4) |
| */ |
| struct scsi_sense_osd_attr_id |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_OSD_ATTR_ID 0x08 |
| uint8_t length; |
| uint8_t reserved[2]; |
| uint8_t attr_desc[0]; |
| }; |
| |
| /* |
| * ATA Return descriptor, used for the SCSI ATA PASS-THROUGH(12), (16) and |
| * (32) commands. Described in SAT-4r05. |
| */ |
| struct scsi_sense_ata_ret_desc |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_ATA 0x09 |
| uint8_t length; |
| uint8_t flags; |
| #define SSD_DESC_ATA_FLAG_EXTEND 0x01 |
| uint8_t error; |
| uint8_t count_15_8; |
| uint8_t count_7_0; |
| uint8_t lba_31_24; |
| uint8_t lba_7_0; |
| uint8_t lba_39_32; |
| uint8_t lba_15_8; |
| uint8_t lba_47_40; |
| uint8_t lba_23_16; |
| uint8_t device; |
| uint8_t status; |
| }; |
| /* |
| * Used with Sense keys No Sense (0x00) and Not Ready (0x02). |
| * |
| * Maximum descriptors allowed: 32 (as of SPC-4) |
| */ |
| struct scsi_sense_progress |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_PROGRESS 0x0a |
| uint8_t length; |
| uint8_t sense_key; |
| uint8_t add_sense_code; |
| uint8_t add_sense_code_qual; |
| uint8_t reserved; |
| uint8_t progress[2]; |
| }; |
| |
| /* |
| * This is typically forwarded as the result of an EXTENDED COPY command. |
| * |
| * Maximum descriptors allowed: 2 (as of SPC-4) |
| */ |
| struct scsi_sense_forwarded |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_FORWARDED 0x0c |
| uint8_t length; |
| uint8_t byte2; |
| #define SSD_FORWARDED_FSDT 0x80 |
| #define SSD_FORWARDED_SDS_MASK 0x0f |
| #define SSD_FORWARDED_SDS_UNK 0x00 |
| #define SSD_FORWARDED_SDS_EXSRC 0x01 |
| #define SSD_FORWARDED_SDS_EXDST 0x02 |
| }; |
| |
| /* |
| * Vendor-specific sense descriptor. The desc_type field will be in the |
| * range between MIN and MAX inclusive. |
| */ |
| struct scsi_sense_vendor |
| { |
| uint8_t desc_type; |
| #define SSD_DESC_VENDOR_MIN 0x80 |
| #define SSD_DESC_VENDOR_MAX 0xff |
| uint8_t length; |
| uint8_t data[0]; |
| }; |
| |
| struct scsi_mode_header_6 |
| { |
| u_int8_t data_length; /* Sense data length */ |
| u_int8_t medium_type; |
| u_int8_t dev_spec; |
| u_int8_t blk_desc_len; |
| }; |
| |
| struct scsi_mode_header_10 |
| { |
| u_int8_t data_length[2];/* Sense data length */ |
| u_int8_t medium_type; |
| u_int8_t dev_spec; |
| u_int8_t unused[2]; |
| u_int8_t blk_desc_len[2]; |
| }; |
| |
| struct scsi_mode_page_header |
| { |
| u_int8_t page_code; |
| #define SMPH_PS 0x80 |
| #define SMPH_SPF 0x40 |
| #define SMPH_PC_MASK 0x3f |
| u_int8_t page_length; |
| }; |
| |
| struct scsi_mode_page_header_sp |
| { |
| uint8_t page_code; |
| uint8_t subpage; |
| uint8_t page_length[2]; |
| }; |
| |
| |
| struct scsi_mode_blk_desc |
| { |
| u_int8_t density; |
| u_int8_t nblocks[3]; |
| u_int8_t reserved; |
| u_int8_t blklen[3]; |
| }; |
| |
| #define SCSI_DEFAULT_DENSITY 0x00 /* use 'default' density */ |
| #define SCSI_SAME_DENSITY 0x7f /* use 'same' density- >= SCSI-2 only */ |
| |
| |
| /* |
| * Status Byte |
| */ |
| #define SCSI_STATUS_OK 0x00 |
| #define SCSI_STATUS_CHECK_COND 0x02 |
| #define SCSI_STATUS_COND_MET 0x04 |
| #define SCSI_STATUS_BUSY 0x08 |
| #define SCSI_STATUS_INTERMED 0x10 |
| #define SCSI_STATUS_INTERMED_COND_MET 0x14 |
| #define SCSI_STATUS_RESERV_CONFLICT 0x18 |
| #define SCSI_STATUS_CMD_TERMINATED 0x22 /* Obsolete in SAM-2 */ |
| #define SCSI_STATUS_QUEUE_FULL 0x28 |
| #define SCSI_STATUS_ACA_ACTIVE 0x30 |
| #define SCSI_STATUS_TASK_ABORTED 0x40 |
| |
| struct scsi_inquiry_pattern { |
| u_int8_t type; |
| u_int8_t media_type; |
| #define SIP_MEDIA_REMOVABLE 0x01 |
| #define SIP_MEDIA_FIXED 0x02 |
| const char *vendor; |
| const char *product; |
| const char *revision; |
| }; |
| |
| struct scsi_static_inquiry_pattern { |
| u_int8_t type; |
| u_int8_t media_type; |
| char vendor[SID_VENDOR_SIZE+1]; |
| char product[SID_PRODUCT_SIZE+1]; |
| char revision[SID_REVISION_SIZE+1]; |
| }; |
| |
| struct scsi_sense_quirk_entry { |
| struct scsi_inquiry_pattern inq_pat; |
| int num_sense_keys; |
| int num_ascs; |
| struct sense_key_table_entry *sense_key_info; |
| struct asc_table_entry *asc_info; |
| }; |
| |
| struct sense_key_table_entry { |
| u_int8_t sense_key; |
| u_int32_t action; |
| const char *desc; |
| }; |
| |
| struct asc_table_entry { |
| u_int8_t asc; |
| u_int8_t ascq; |
| u_int32_t action; |
| const char *desc; |
| }; |
| |
| struct op_table_entry { |
| u_int8_t opcode; |
| u_int32_t opmask; |
| const char *desc; |
| }; |
| |
| struct scsi_op_quirk_entry { |
| struct scsi_inquiry_pattern inq_pat; |
| int num_ops; |
| struct op_table_entry *op_table; |
| }; |
| |
| typedef enum { |
| SSS_FLAG_NONE = 0x00, |
| SSS_FLAG_PRINT_COMMAND = 0x01 |
| } scsi_sense_string_flags; |
| |
| struct scsi_nv { |
| const char *name; |
| uint64_t value; |
| }; |
| |
| typedef enum { |
| SCSI_NV_FOUND, |
| SCSI_NV_AMBIGUOUS, |
| SCSI_NV_NOT_FOUND |
| } scsi_nv_status; |
| |
| typedef enum { |
| SCSI_NV_FLAG_NONE = 0x00, |
| SCSI_NV_FLAG_IG_CASE = 0x01 /* Case insensitive comparison */ |
| } scsi_nv_flags; |
| |
| struct ccb_scsiio; |
| struct cam_periph; |
| union ccb; |
| #ifndef _KERNEL |
| struct cam_device; |
| #endif |
| |
| extern const char *scsi_sense_key_text[]; |
| |
| __BEGIN_DECLS |
| void scsi_sense_desc(int sense_key, int asc, int ascq, |
| struct scsi_inquiry_data *inq_data, |
| const char **sense_key_desc, const char **asc_desc); |
| scsi_sense_action scsi_error_action(struct ccb_scsiio* csio, |
| struct scsi_inquiry_data *inq_data, |
| u_int32_t sense_flags); |
| const char * scsi_status_string(struct ccb_scsiio *csio); |
| |
| void scsi_desc_iterate(struct scsi_sense_data_desc *sense, u_int sense_len, |
| int (*iter_func)(struct scsi_sense_data_desc *sense, |
| u_int, struct scsi_sense_desc_header *, |
| void *), void *arg); |
| uint8_t *scsi_find_desc(struct scsi_sense_data_desc *sense, u_int sense_len, |
| uint8_t desc_type); |
| void scsi_set_sense_data(struct scsi_sense_data *sense_data, |
| scsi_sense_data_type sense_format, int current_error, |
| int sense_key, int asc, int ascq, ...) ; |
| void scsi_set_sense_data_va(struct scsi_sense_data *sense_data, |
| scsi_sense_data_type sense_format, |
| int current_error, int sense_key, int asc, |
| int ascq, va_list ap); |
| int scsi_get_sense_info(struct scsi_sense_data *sense_data, u_int sense_len, |
| uint8_t info_type, uint64_t *info, |
| int64_t *signed_info); |
| int scsi_get_sks(struct scsi_sense_data *sense_data, u_int sense_len, |
| uint8_t *sks); |
| int scsi_get_block_info(struct scsi_sense_data *sense_data, u_int sense_len, |
| struct scsi_inquiry_data *inq_data, |
| uint8_t *block_bits); |
| int scsi_get_stream_info(struct scsi_sense_data *sense_data, u_int sense_len, |
| struct scsi_inquiry_data *inq_data, |
| uint8_t *stream_bits); |
| void scsi_info_sbuf(struct sbuf *sb, uint8_t *cdb, int cdb_len, |
| struct scsi_inquiry_data *inq_data, uint64_t info); |
| void scsi_command_sbuf(struct sbuf *sb, uint8_t *cdb, int cdb_len, |
| struct scsi_inquiry_data *inq_data, uint64_t csi); |
| void scsi_progress_sbuf(struct sbuf *sb, uint16_t progress); |
| int scsi_sks_sbuf(struct sbuf *sb, int sense_key, uint8_t *sks); |
| void scsi_fru_sbuf(struct sbuf *sb, uint64_t fru); |
| void scsi_stream_sbuf(struct sbuf *sb, uint8_t stream_bits, uint64_t info); |
| void scsi_block_sbuf(struct sbuf *sb, uint8_t block_bits, uint64_t info); |
| void scsi_sense_info_sbuf(struct sbuf *sb, struct scsi_sense_data *sense, |
| u_int sense_len, uint8_t *cdb, int cdb_len, |
| struct scsi_inquiry_data *inq_data, |
| struct scsi_sense_desc_header *header); |
| |
| void scsi_sense_command_sbuf(struct sbuf *sb, struct scsi_sense_data *sense, |
| u_int sense_len, uint8_t *cdb, int cdb_len, |
| struct scsi_inquiry_data *inq_data, |
| struct scsi_sense_desc_header *header); |
| void scsi_sense_sks_sbuf(struct sbuf *sb, struct scsi_sense_data *sense, |
| u_int sense_len, uint8_t *cdb, int cdb_len, |
| struct scsi_inquiry_data *inq_data, |
| struct scsi_sense_desc_header *header); |
| void scsi_sense_fru_sbuf(struct sbuf *sb, struct scsi_sense_data *sense, |
| u_int sense_len, uint8_t *cdb, int cdb_len, |
| struct scsi_inquiry_data *inq_data, |
| struct scsi_sense_desc_header *header); |
| void scsi_sense_stream_sbuf(struct sbuf *sb, struct scsi_sense_data *sense, |
| u_int sense_len, uint8_t *cdb, int cdb_len, |
| struct scsi_inquiry_data *inq_data, |
| struct scsi_sense_desc_header *header); |
| void scsi_sense_block_sbuf(struct sbuf *sb, struct scsi_sense_data *sense, |
| u_int sense_len, uint8_t *cdb, int cdb_len, |
| struct scsi_inquiry_data *inq_data, |
| struct scsi_sense_desc_header *header); |
| void scsi_sense_progress_sbuf(struct sbuf *sb, struct scsi_sense_data *sense, |
| u_int sense_len, uint8_t *cdb, int cdb_len, |
| struct scsi_inquiry_data *inq_data, |
| struct scsi_sense_desc_header *header); |
| void scsi_sense_generic_sbuf(struct sbuf *sb, struct scsi_sense_data *sense, |
| u_int sense_len, uint8_t *cdb, int cdb_len, |
| struct scsi_inquiry_data *inq_data, |
| struct scsi_sense_desc_header *header); |
| void scsi_sense_desc_sbuf(struct sbuf *sb, struct scsi_sense_data *sense, |
| u_int sense_len, uint8_t *cdb, int cdb_len, |
| struct scsi_inquiry_data *inq_data, |
| struct scsi_sense_desc_header *header); |
| scsi_sense_data_type scsi_sense_type(struct scsi_sense_data *sense_data); |
| |
| void scsi_sense_only_sbuf(struct scsi_sense_data *sense, u_int sense_len, |
| struct sbuf *sb, char *path_str, |
| struct scsi_inquiry_data *inq_data, uint8_t *cdb, |
| int cdb_len); |
| |
| #ifdef _KERNEL |
| int scsi_command_string(struct ccb_scsiio *csio, struct sbuf *sb); |
| int scsi_sense_sbuf(struct ccb_scsiio *csio, struct sbuf *sb, |
| scsi_sense_string_flags flags); |
| char * scsi_sense_string(struct ccb_scsiio *csio, |
| char *str, int str_len); |
| void scsi_sense_print(struct ccb_scsiio *csio); |
| int scsi_vpd_supported_page(struct cam_periph *periph, |
| uint8_t page_id); |
| #else /* _KERNEL */ |
| int scsi_command_string(struct cam_device *device, |
| struct ccb_scsiio *csio, struct sbuf *sb); |
| int scsi_sense_sbuf(struct cam_device *device, |
| struct ccb_scsiio *csio, struct sbuf *sb, |
| scsi_sense_string_flags flags); |
| char * scsi_sense_string(struct cam_device *device, |
| struct ccb_scsiio *csio, |
| char *str, int str_len); |
| void scsi_sense_print(struct cam_device *device, |
| struct ccb_scsiio *csio, FILE *ofile); |
| #endif /* _KERNEL */ |
| |
| const char * scsi_op_desc(u_int16_t opcode, |
| struct scsi_inquiry_data *inq_data); |
| char * scsi_cdb_string(u_int8_t *cdb_ptr, char *cdb_string, |
| size_t len); |
| void scsi_cdb_sbuf(u_int8_t *cdb_ptr, struct sbuf *sb); |
| |
| void scsi_print_inquiry(struct scsi_inquiry_data *inq_data); |
| void scsi_print_inquiry_short(struct scsi_inquiry_data *inq_data); |
| |
| u_int scsi_calc_syncsrate(u_int period_factor); |
| u_int scsi_calc_syncparam(u_int period); |
| |
| typedef int (*scsi_devid_checkfn_t)(uint8_t *); |
| int scsi_devid_is_naa_ieee_reg(uint8_t *bufp); |
| int scsi_devid_is_sas_target(uint8_t *bufp); |
| int scsi_devid_is_lun_eui64(uint8_t *bufp); |
| int scsi_devid_is_lun_naa(uint8_t *bufp); |
| int scsi_devid_is_lun_name(uint8_t *bufp); |
| int scsi_devid_is_lun_t10(uint8_t *bufp); |
| int scsi_devid_is_port_naa(uint8_t *bufp); |
| struct scsi_vpd_id_descriptor * |
| scsi_get_devid(struct scsi_vpd_device_id *id, uint32_t len, |
| scsi_devid_checkfn_t ck_fn); |
| struct scsi_vpd_id_descriptor * |
| scsi_get_devid_desc(struct scsi_vpd_id_descriptor *desc, uint32_t len, |
| scsi_devid_checkfn_t ck_fn); |
| |
| int scsi_transportid_sbuf(struct sbuf *sb, |
| struct scsi_transportid_header *hdr, |
| uint32_t valid_len); |
| |
| const char * scsi_nv_to_str(struct scsi_nv *table, int num_table_entries, |
| uint64_t value); |
| |
| scsi_nv_status scsi_get_nv(struct scsi_nv *table, int num_table_entries, |
| char *name, int *table_entry, scsi_nv_flags flags); |
| |
| int scsi_parse_transportid_64bit(int proto_id, char *id_str, |
| struct scsi_transportid_header **hdr, |
| unsigned int *alloc_len, |
| #ifdef _KERNEL |
| struct malloc_type *type, int flags, |
| #endif |
| char *error_str, int error_str_len); |
| |
| int scsi_parse_transportid_spi(char *id_str, |
| struct scsi_transportid_header **hdr, |
| unsigned int *alloc_len, |
| #ifdef _KERNEL |
| struct malloc_type *type, int flags, |
| #endif |
| char *error_str, int error_str_len); |
| |
| int scsi_parse_transportid_rdma(char *id_str, |
| struct scsi_transportid_header **hdr, |
| unsigned int *alloc_len, |
| #ifdef _KERNEL |
| struct malloc_type *type, int flags, |
| #endif |
| char *error_str, int error_str_len); |
| |
| int scsi_parse_transportid_iscsi(char *id_str, |
| struct scsi_transportid_header **hdr, |
| unsigned int *alloc_len, |
| #ifdef _KERNEL |
| struct malloc_type *type, int flags, |
| #endif |
| char *error_str,int error_str_len); |
| |
| int scsi_parse_transportid_sop(char *id_str, |
| struct scsi_transportid_header **hdr, |
| unsigned int *alloc_len, |
| #ifdef _KERNEL |
| struct malloc_type *type, int flags, |
| #endif |
| char *error_str,int error_str_len); |
| |
| int scsi_parse_transportid(char *transportid_str, |
| struct scsi_transportid_header **hdr, |
| unsigned int *alloc_len, |
| #ifdef _KERNEL |
| struct malloc_type *type, int flags, |
| #endif |
| char *error_str, int error_str_len); |
| |
| |
| int scsi_attrib_volcoh_sbuf(struct sbuf *sb, |
| struct scsi_mam_attribute_header *hdr, |
| uint32_t valid_len, uint32_t flags, |
| uint32_t output_flags, char *error_str, |
| int error_str_len); |
| |
| int scsi_attrib_vendser_sbuf(struct sbuf *sb, |
| struct scsi_mam_attribute_header *hdr, |
| uint32_t valid_len, uint32_t flags, |
| uint32_t output_flags, char *error_str, |
| int error_str_len); |
| |
| int scsi_attrib_hexdump_sbuf(struct sbuf *sb, |
| struct scsi_mam_attribute_header *hdr, |
| uint32_t valid_len, uint32_t flags, |
| uint32_t output_flags, char *error_str, |
| int error_str_len); |
| |
| int scsi_attrib_int_sbuf(struct sbuf *sb, struct scsi_mam_attribute_header *hdr, |
| uint32_t valid_len, uint32_t flags, |
| uint32_t output_flags, char *error_str, |
| int error_str_len); |
| |
| int scsi_attrib_ascii_sbuf(struct sbuf *sb, |
| struct scsi_mam_attribute_header *hdr, |
| uint32_t valid_len, uint32_t flags, |
| uint32_t output_flags, char *error_str, |
| int error_str_len); |
| |
| int scsi_attrib_text_sbuf(struct sbuf *sb, |
| struct scsi_mam_attribute_header *hdr, |
| uint32_t valid_len, uint32_t flags, |
| uint32_t output_flags, char *error_str, |
| int error_str_len); |
| |
| struct scsi_attrib_table_entry *scsi_find_attrib_entry( |
| struct scsi_attrib_table_entry *table, |
| size_t num_table_entries, uint32_t id); |
| |
| struct scsi_attrib_table_entry *scsi_get_attrib_entry(uint32_t id); |
| |
| int scsi_attrib_value_sbuf(struct sbuf *sb, uint32_t valid_len, |
| struct scsi_mam_attribute_header *hdr, |
| uint32_t output_flags, char *error_str, |
| size_t error_str_len); |
| |
| void scsi_attrib_prefix_sbuf(struct sbuf *sb, uint32_t output_flags, |
| struct scsi_mam_attribute_header *hdr, |
| uint32_t valid_len, const char *desc); |
| |
| int scsi_attrib_sbuf(struct sbuf *sb, struct scsi_mam_attribute_header *hdr, |
| uint32_t valid_len, |
| struct scsi_attrib_table_entry *user_table, |
| size_t num_user_entries, int prefer_user_table, |
| uint32_t output_flags, char *error_str, int error_str_len); |
| |
| void scsi_test_unit_ready(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), |
| u_int8_t tag_action, |
| u_int8_t sense_len, u_int32_t timeout); |
| |
| void scsi_request_sense(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), |
| void *data_ptr, u_int8_t dxfer_len, |
| u_int8_t tag_action, u_int8_t sense_len, |
| u_int32_t timeout); |
| |
| void scsi_inquiry(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| u_int8_t tag_action, u_int8_t *inq_buf, |
| u_int32_t inq_len, int evpd, u_int8_t page_code, |
| u_int8_t sense_len, u_int32_t timeout); |
| |
| void scsi_mode_sense(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), |
| u_int8_t tag_action, int dbd, |
| u_int8_t page_code, u_int8_t page, |
| u_int8_t *param_buf, u_int32_t param_len, |
| u_int8_t sense_len, u_int32_t timeout); |
| |
| void scsi_mode_sense_len(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), |
| u_int8_t tag_action, int dbd, |
| u_int8_t page_code, u_int8_t page, |
| u_int8_t *param_buf, u_int32_t param_len, |
| int minimum_cmd_size, u_int8_t sense_len, |
| u_int32_t timeout); |
| |
| void scsi_mode_select(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), |
| u_int8_t tag_action, int scsi_page_fmt, |
| int save_pages, u_int8_t *param_buf, |
| u_int32_t param_len, u_int8_t sense_len, |
| u_int32_t timeout); |
| |
| void scsi_mode_select_len(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), |
| u_int8_t tag_action, int scsi_page_fmt, |
| int save_pages, u_int8_t *param_buf, |
| u_int32_t param_len, int minimum_cmd_size, |
| u_int8_t sense_len, u_int32_t timeout); |
| |
| void scsi_log_sense(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| u_int8_t tag_action, u_int8_t page_code, |
| u_int8_t page, int save_pages, int ppc, |
| u_int32_t paramptr, u_int8_t *param_buf, |
| u_int32_t param_len, u_int8_t sense_len, |
| u_int32_t timeout); |
| |
| void scsi_log_select(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), u_int8_t tag_action, |
| u_int8_t page_code, int save_pages, |
| int pc_reset, u_int8_t *param_buf, |
| u_int32_t param_len, u_int8_t sense_len, |
| u_int32_t timeout); |
| |
| void scsi_prevent(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| u_int8_t tag_action, u_int8_t action, |
| u_int8_t sense_len, u_int32_t timeout); |
| |
| void scsi_read_capacity(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), u_int8_t tag_action, |
| struct scsi_read_capacity_data *, |
| u_int8_t sense_len, u_int32_t timeout); |
| void scsi_read_capacity_16(struct ccb_scsiio *csio, uint32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), uint8_t tag_action, |
| uint64_t lba, int reladr, int pmi, |
| uint8_t *rcap_buf, int rcap_buf_len, |
| uint8_t sense_len, uint32_t timeout); |
| |
| void scsi_report_luns(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), u_int8_t tag_action, |
| u_int8_t select_report, |
| struct scsi_report_luns_data *rpl_buf, |
| u_int32_t alloc_len, u_int8_t sense_len, |
| u_int32_t timeout); |
| |
| void scsi_report_target_group(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), u_int8_t tag_action, |
| u_int8_t pdf, |
| void *buf, |
| u_int32_t alloc_len, u_int8_t sense_len, |
| u_int32_t timeout); |
| |
| void scsi_set_target_group(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), u_int8_t tag_action, void *buf, |
| u_int32_t alloc_len, u_int8_t sense_len, |
| u_int32_t timeout); |
| |
| void scsi_synchronize_cache(struct ccb_scsiio *csio, |
| u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), u_int8_t tag_action, |
| u_int32_t begin_lba, u_int16_t lb_count, |
| u_int8_t sense_len, u_int32_t timeout); |
| |
| void scsi_receive_diagnostic_results(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb*), |
| uint8_t tag_action, int pcv, |
| uint8_t page_code, uint8_t *data_ptr, |
| uint16_t allocation_length, |
| uint8_t sense_len, uint32_t timeout); |
| |
| void scsi_send_diagnostic(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| uint8_t tag_action, int unit_offline, |
| int device_offline, int self_test, int page_format, |
| int self_test_code, uint8_t *data_ptr, |
| uint16_t param_list_length, uint8_t sense_len, |
| uint32_t timeout); |
| |
| void scsi_read_buffer(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb*), |
| uint8_t tag_action, int mode, |
| uint8_t buffer_id, u_int32_t offset, |
| uint8_t *data_ptr, uint32_t allocation_length, |
| uint8_t sense_len, uint32_t timeout); |
| |
| void scsi_write_buffer(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| uint8_t tag_action, int mode, |
| uint8_t buffer_id, u_int32_t offset, |
| uint8_t *data_ptr, uint32_t param_list_length, |
| uint8_t sense_len, uint32_t timeout); |
| |
| #define SCSI_RW_READ 0x0001 |
| #define SCSI_RW_WRITE 0x0002 |
| #define SCSI_RW_DIRMASK 0x0003 |
| #define SCSI_RW_BIO 0x1000 |
| void scsi_read_write(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| u_int8_t tag_action, int readop, u_int8_t byte2, |
| int minimum_cmd_size, u_int64_t lba, |
| u_int32_t block_count, u_int8_t *data_ptr, |
| u_int32_t dxfer_len, u_int8_t sense_len, |
| u_int32_t timeout); |
| |
| void scsi_write_same(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| u_int8_t tag_action, u_int8_t byte2, |
| int minimum_cmd_size, u_int64_t lba, |
| u_int32_t block_count, u_int8_t *data_ptr, |
| u_int32_t dxfer_len, u_int8_t sense_len, |
| u_int32_t timeout); |
| |
| void scsi_ata_identify(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| u_int8_t tag_action, u_int8_t *data_ptr, |
| u_int16_t dxfer_len, u_int8_t sense_len, |
| u_int32_t timeout); |
| |
| void scsi_ata_trim(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| u_int8_t tag_action, u_int16_t block_count, |
| u_int8_t *data_ptr, u_int16_t dxfer_len, |
| u_int8_t sense_len, u_int32_t timeout); |
| |
| int scsi_ata_read_log(struct ccb_scsiio *csio, uint32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| uint8_t tag_action, uint32_t log_address, |
| uint32_t page_number, uint16_t block_count, |
| uint8_t protocol, uint8_t *data_ptr, uint32_t dxfer_len, |
| uint8_t sense_len, uint32_t timeout); |
| |
| int scsi_ata_pass(struct ccb_scsiio *csio, uint32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| uint32_t flags, uint8_t tag_action, |
| uint8_t protocol, uint8_t ata_flags, uint16_t features, |
| uint16_t sector_count, uint64_t lba, uint8_t command, |
| uint8_t device, uint8_t icc, uint32_t auxiliary, |
| uint8_t control, u_int8_t *data_ptr, uint32_t dxfer_len, |
| uint8_t *cdb_storage, size_t cdb_storage_len, |
| int minimum_cmd_size, u_int8_t sense_len, u_int32_t timeout); |
| |
| void scsi_ata_pass_16(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| u_int32_t flags, u_int8_t tag_action, |
| u_int8_t protocol, u_int8_t ata_flags, u_int16_t features, |
| u_int16_t sector_count, uint64_t lba, u_int8_t command, |
| u_int8_t control, u_int8_t *data_ptr, u_int16_t dxfer_len, |
| u_int8_t sense_len, u_int32_t timeout); |
| |
| void scsi_unmap(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| u_int8_t tag_action, u_int8_t byte2, |
| u_int8_t *data_ptr, u_int16_t dxfer_len, |
| u_int8_t sense_len, u_int32_t timeout); |
| |
| void scsi_start_stop(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| u_int8_t tag_action, int start, int load_eject, |
| int immediate, u_int8_t sense_len, u_int32_t timeout); |
| void scsi_read_attribute(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| u_int8_t tag_action, u_int8_t service_action, |
| uint32_t element, u_int8_t elem_type, |
| int logical_volume, int partition, |
| u_int32_t first_attribute, int cache, u_int8_t *data_ptr, |
| u_int32_t length, int sense_len, u_int32_t timeout); |
| void scsi_write_attribute(struct ccb_scsiio *csio, u_int32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| u_int8_t tag_action, uint32_t element, |
| int logical_volume, int partition, int wtc, u_int8_t *data_ptr, |
| u_int32_t length, int sense_len, u_int32_t timeout); |
| |
| void scsi_security_protocol_in(struct ccb_scsiio *csio, uint32_t retries, |
| void (*cbfcnp)(struct cam_periph *, union ccb *), |
| uint8_t tag_action, uint32_t security_protocol, |
| uint32_t security_protocol_specific, int byte4, |
| uint8_t *data_ptr, uint32_t dxfer_len, |
| int sense_len, int timeout); |
| |
| void scsi_security_protocol_out(struct ccb_scsiio *csio, uint32_t retries, |
| void (*cbfcnp)(struct cam_periph *,union ccb *), |
| uint8_t tag_action, uint32_t security_protocol, |
| uint32_t security_protocol_specific, int byte4, |
| uint8_t *data_ptr, uint32_t dxfer_len, |
| int sense_len, int timeout); |
| |
| void scsi_persistent_reserve_in(struct ccb_scsiio *csio, uint32_t retries, |
| void (*cbfcnp)(struct cam_periph *,union ccb *), |
| uint8_t tag_action, int service_action, |
| uint8_t *data_ptr, uint32_t dxfer_len, |
| int sense_len, int timeout); |
| |
| void scsi_persistent_reserve_out(struct ccb_scsiio *csio, uint32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), |
| uint8_t tag_action, int service_action, |
| int scope, int res_type, uint8_t *data_ptr, |
| uint32_t dxfer_len, int sense_len, |
| int timeout); |
| |
| void scsi_report_supported_opcodes(struct ccb_scsiio *csio, uint32_t retries, |
| void (*cbfcnp)(struct cam_periph *, |
| union ccb *), |
| uint8_t tag_action, int options, |
| int req_opcode, int req_service_action, |
| uint8_t *data_ptr, uint32_t dxfer_len, |
| int sense_len, int timeout); |
| |
| int scsi_inquiry_match(caddr_t inqbuffer, caddr_t table_entry); |
| int scsi_static_inquiry_match(caddr_t inqbuffer, |
| caddr_t table_entry); |
| int scsi_devid_match(uint8_t *rhs, size_t rhs_len, |
| uint8_t *lhs, size_t lhs_len); |
| |
| void scsi_extract_sense(struct scsi_sense_data *sense, int *error_code, |
| int *sense_key, int *asc, int *ascq); |
| int scsi_extract_sense_ccb(union ccb *ccb, int *error_code, int *sense_key, |
| int *asc, int *ascq); |
| void scsi_extract_sense_len(struct scsi_sense_data *sense, |
| u_int sense_len, int *error_code, int *sense_key, |
| int *asc, int *ascq, int show_errors); |
| int scsi_get_sense_key(struct scsi_sense_data *sense, u_int sense_len, |
| int show_errors); |
| int scsi_get_asc(struct scsi_sense_data *sense, u_int sense_len, |
| int show_errors); |
| int scsi_get_ascq(struct scsi_sense_data *sense, u_int sense_len, |
| int show_errors); |
| static __inline void scsi_ulto2b(u_int32_t val, u_int8_t *bytes); |
| static __inline void scsi_ulto3b(u_int32_t val, u_int8_t *bytes); |
| static __inline void scsi_ulto4b(u_int32_t val, u_int8_t *bytes); |
| static __inline void scsi_u64to8b(u_int64_t val, u_int8_t *bytes); |
| static __inline uint32_t scsi_2btoul(const uint8_t *bytes); |
| static __inline uint32_t scsi_3btoul(const uint8_t *bytes); |
| static __inline int32_t scsi_3btol(const uint8_t *bytes); |
| static __inline uint32_t scsi_4btoul(const uint8_t *bytes); |
| static __inline uint64_t scsi_8btou64(const uint8_t *bytes); |
| static __inline void *find_mode_page_6(struct scsi_mode_header_6 *mode_header); |
| static __inline void *find_mode_page_10(struct scsi_mode_header_10 *mode_header); |
| |
| static __inline void |
| scsi_ulto2b(u_int32_t val, u_int8_t *bytes) |
| { |
| |
| bytes[0] = (val >> 8) & 0xff; |
| bytes[1] = val & 0xff; |
| } |
| |
| static __inline void |
| scsi_ulto3b(u_int32_t val, u_int8_t *bytes) |
| { |
| |
| bytes[0] = (val >> 16) & 0xff; |
| bytes[1] = (val >> 8) & 0xff; |
| bytes[2] = val & 0xff; |
| } |
| |
| static __inline void |
| scsi_ulto4b(u_int32_t val, u_int8_t *bytes) |
| { |
| |
| bytes[0] = (val >> 24) & 0xff; |
| bytes[1] = (val >> 16) & 0xff; |
| bytes[2] = (val >> 8) & 0xff; |
| bytes[3] = val & 0xff; |
| } |
| |
| static __inline void |
| scsi_u64to8b(u_int64_t val, u_int8_t *bytes) |
| { |
| |
| bytes[0] = (val >> 56) & 0xff; |
| bytes[1] = (val >> 48) & 0xff; |
| bytes[2] = (val >> 40) & 0xff; |
| bytes[3] = (val >> 32) & 0xff; |
| bytes[4] = (val >> 24) & 0xff; |
| bytes[5] = (val >> 16) & 0xff; |
| bytes[6] = (val >> 8) & 0xff; |
| bytes[7] = val & 0xff; |
| } |
| |
| static __inline uint32_t |
| scsi_2btoul(const uint8_t *bytes) |
| { |
| uint32_t rv; |
| |
| rv = (bytes[0] << 8) | |
| bytes[1]; |
| return (rv); |
| } |
| |
| static __inline uint32_t |
| scsi_3btoul(const uint8_t *bytes) |
| { |
| uint32_t rv; |
| |
| rv = (bytes[0] << 16) | |
| (bytes[1] << 8) | |
| bytes[2]; |
| return (rv); |
| } |
| |
| static __inline int32_t |
| scsi_3btol(const uint8_t *bytes) |
| { |
| uint32_t rc = scsi_3btoul(bytes); |
| |
| if (rc & 0x00800000) |
| rc |= 0xff000000; |
| |
| return (int32_t) rc; |
| } |
| |
| static __inline uint32_t |
| scsi_4btoul(const uint8_t *bytes) |
| { |
| uint32_t rv; |
| |
| rv = (bytes[0] << 24) | |
| (bytes[1] << 16) | |
| (bytes[2] << 8) | |
| bytes[3]; |
| return (rv); |
| } |
| |
| static __inline uint64_t |
| scsi_8btou64(const uint8_t *bytes) |
| { |
| uint64_t rv; |
| |
| rv = (((uint64_t)bytes[0]) << 56) | |
| (((uint64_t)bytes[1]) << 48) | |
| (((uint64_t)bytes[2]) << 40) | |
| (((uint64_t)bytes[3]) << 32) | |
| (((uint64_t)bytes[4]) << 24) | |
| (((uint64_t)bytes[5]) << 16) | |
| (((uint64_t)bytes[6]) << 8) | |
| bytes[7]; |
| return (rv); |
| } |
| |
| /* |
| * Given the pointer to a returned mode sense buffer, return a pointer to |
| * the start of the first mode page. |
| */ |
| static __inline void * |
| find_mode_page_6(struct scsi_mode_header_6 *mode_header) |
| { |
| void *page_start; |
| |
| page_start = (void *)((u_int8_t *)&mode_header[1] + |
| mode_header->blk_desc_len); |
| |
| return(page_start); |
| } |
| |
| static __inline void * |
| find_mode_page_10(struct scsi_mode_header_10 *mode_header) |
| { |
| void *page_start; |
| |
| page_start = (void *)((u_int8_t *)&mode_header[1] + |
| scsi_2btoul(mode_header->blk_desc_len)); |
| |
| return(page_start); |
| } |
| |
| __END_DECLS |
| |
| #endif /*_SCSI_SCSI_ALL_H*/ |