| /* |
| * Copyright (C) 2013 The Android Open Source Project |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| */ |
| |
| #define LOG_TAG "audio_hw_primary" |
| /*#define LOG_NDEBUG 0*/ |
| #define LOG_NDDEBUG 0 |
| |
| #include <errno.h> |
| #include <pthread.h> |
| #include <stdint.h> |
| #include <sys/time.h> |
| #include <stdlib.h> |
| #include <dlfcn.h> |
| #include <math.h> |
| |
| #include <cutils/log.h> |
| #include <cutils/str_parms.h> |
| #include <cutils/properties.h> |
| #include <cutils/list.h> |
| |
| #include "audio_hw.h" |
| |
| #define LIB_ACDB_LOADER "/system/lib/libacdbloader.so" |
| #define LIB_CSD_CLIENT "/system/lib/libcsd-client.so" |
| #define MIXER_XML_PATH "/system/etc/mixer_paths.xml" |
| #define MIXER_CARD 0 |
| |
| #define STRING_TO_ENUM(string) { #string, string } |
| |
| /* Flags used to initialize acdb_settings variable that goes to ACDB library */ |
| #define DMIC_FLAG 0x00000002 |
| #define TTY_MODE_OFF 0x00000010 |
| #define TTY_MODE_FULL 0x00000020 |
| #define TTY_MODE_VCO 0x00000040 |
| #define TTY_MODE_HCO 0x00000080 |
| #define TTY_MODE_CLEAR 0xFFFFFF0F |
| |
| struct string_to_enum { |
| const char *name; |
| uint32_t value; |
| }; |
| |
| static const struct string_to_enum out_channels_name_to_enum_table[] = { |
| STRING_TO_ENUM(AUDIO_CHANNEL_OUT_STEREO), |
| STRING_TO_ENUM(AUDIO_CHANNEL_OUT_5POINT1), |
| STRING_TO_ENUM(AUDIO_CHANNEL_OUT_7POINT1), |
| }; |
| |
| static const char * const use_case_table[AUDIO_USECASE_MAX] = { |
| [USECASE_AUDIO_PLAYBACK_DEEP_BUFFER] = "deep-buffer-playback", |
| [USECASE_AUDIO_PLAYBACK_LOW_LATENCY] = "low-latency-playback", |
| [USECASE_AUDIO_PLAYBACK_MULTI_CH] = "multi-channel-playback", |
| [USECASE_AUDIO_RECORD] = "audio-record", |
| [USECASE_AUDIO_RECORD_LOW_LATENCY] = "low-latency-record", |
| [USECASE_VOICE_CALL] = "voice-call", |
| }; |
| |
| static const int pcm_device_table[AUDIO_USECASE_MAX][2] = { |
| [USECASE_AUDIO_PLAYBACK_DEEP_BUFFER] = {0, 0}, |
| [USECASE_AUDIO_PLAYBACK_LOW_LATENCY] = {14, 14}, |
| [USECASE_AUDIO_PLAYBACK_MULTI_CH] = {1, 1}, |
| [USECASE_AUDIO_RECORD] = {0, 0}, |
| [USECASE_AUDIO_RECORD_LOW_LATENCY] = {14, 14}, |
| [USECASE_VOICE_CALL] = {12, 12}, |
| }; |
| |
| /* Array to store sound devices */ |
| static const char * const device_table[SND_DEVICE_MAX] = { |
| [SND_DEVICE_NONE] = "none", |
| /* Playback sound devices */ |
| [SND_DEVICE_OUT_HANDSET] = "handset", |
| [SND_DEVICE_OUT_SPEAKER] = "speaker", |
| [SND_DEVICE_OUT_HEADPHONES] = "headphones", |
| [SND_DEVICE_OUT_SPEAKER_AND_HEADPHONES] = "speaker-and-headphones", |
| [SND_DEVICE_OUT_VOICE_SPEAKER] = "voice-speaker", |
| [SND_DEVICE_OUT_VOICE_HEADPHONES] = "voice-headphones", |
| [SND_DEVICE_OUT_HDMI] = "hdmi", |
| [SND_DEVICE_OUT_SPEAKER_AND_HDMI] = "speaker-and-hdmi", |
| [SND_DEVICE_OUT_BT_SCO] = "bt-sco-headset", |
| [SND_DEVICE_OUT_VOICE_HANDSET_TMUS] = "voice-handset-tmus", |
| [SND_DEVICE_OUT_VOICE_TTY_FULL_HEADPHONES] = "voice-tty-full-headphones", |
| [SND_DEVICE_OUT_VOICE_TTY_VCO_HEADPHONES] = "voice-tty-vco-headphones", |
| [SND_DEVICE_OUT_VOICE_TTY_HCO_HANDSET] = "voice-tty-hco-handset", |
| |
| /* Capture sound devices */ |
| [SND_DEVICE_IN_HANDSET_MIC] = "handset-mic", |
| [SND_DEVICE_IN_SPEAKER_MIC] = "speaker-mic", |
| [SND_DEVICE_IN_HEADSET_MIC] = "headset-mic", |
| [SND_DEVICE_IN_VOICE_SPEAKER_MIC] = "voice-speaker-mic", |
| [SND_DEVICE_IN_VOICE_HEADSET_MIC] = "voice-headset-mic", |
| [SND_DEVICE_IN_HDMI_MIC] = "hdmi-mic", |
| [SND_DEVICE_IN_BT_SCO_MIC] = "bt-sco-mic", |
| [SND_DEVICE_IN_CAMCORDER_MIC] = "camcorder-mic", |
| [SND_DEVICE_IN_VOICE_DMIC_EF] = "voice-dmic-ef", |
| [SND_DEVICE_IN_VOICE_DMIC_BS] = "voice-dmic-bs", |
| [SND_DEVICE_IN_VOICE_DMIC_EF_TMUS] = "voice-dmic-ef-tmus", |
| [SND_DEVICE_IN_VOICE_SPEAKER_DMIC_EF] = "voice-speaker-dmic-ef", |
| [SND_DEVICE_IN_VOICE_SPEAKER_DMIC_BS] = "voice-speaker-dmic-bs", |
| [SND_DEVICE_IN_VOICE_TTY_FULL_HEADSET_MIC] = "voice-tty-full-headset-mic", |
| [SND_DEVICE_IN_VOICE_TTY_VCO_HANDSET_MIC] = "voice-tty-vco-handset-mic", |
| [SND_DEVICE_IN_VOICE_TTY_HCO_HEADSET_MIC] = "voice-tty-hco-headset-mic", |
| [SND_DEVICE_IN_VOICE_REC_MIC] = "voice-rec-mic", |
| [SND_DEVICE_IN_VOICE_REC_DMIC_EF] = "voice-rec-dmic-ef", |
| [SND_DEVICE_IN_VOICE_REC_DMIC_BS] = "voice-rec-dmic-bs", |
| [SND_DEVICE_IN_VOICE_REC_DMIC_EF_FLUENCE] = "voice-rec-dmic-ef-fluence", |
| [SND_DEVICE_IN_VOICE_REC_DMIC_BS_FLUENCE] = "voice-rec-dmic-bs-fluence", |
| }; |
| |
| /* ACDB IDs (audio DSP path configuration IDs) for each sound device */ |
| static const int acdb_device_table[SND_DEVICE_MAX] = { |
| [SND_DEVICE_NONE] = -1, |
| [SND_DEVICE_OUT_HANDSET] = 7, |
| [SND_DEVICE_OUT_SPEAKER] = 14, |
| [SND_DEVICE_OUT_HEADPHONES] = 10, |
| [SND_DEVICE_OUT_SPEAKER_AND_HEADPHONES] = 10, |
| [SND_DEVICE_OUT_VOICE_SPEAKER] = 14, |
| [SND_DEVICE_OUT_VOICE_HEADPHONES] = 10, |
| [SND_DEVICE_OUT_HDMI] = 18, |
| [SND_DEVICE_OUT_SPEAKER_AND_HDMI] = 14, |
| [SND_DEVICE_OUT_BT_SCO] = 22, |
| [SND_DEVICE_OUT_VOICE_HANDSET_TMUS] = 81, |
| [SND_DEVICE_OUT_VOICE_TTY_FULL_HEADPHONES] = 17, |
| [SND_DEVICE_OUT_VOICE_TTY_VCO_HEADPHONES] = 17, |
| [SND_DEVICE_OUT_VOICE_TTY_HCO_HANDSET] = 37, |
| |
| [SND_DEVICE_IN_HANDSET_MIC] = 4, |
| [SND_DEVICE_IN_SPEAKER_MIC] = 4, |
| [SND_DEVICE_IN_HEADSET_MIC] = 8, |
| [SND_DEVICE_IN_VOICE_SPEAKER_MIC] = 11, |
| [SND_DEVICE_IN_VOICE_HEADSET_MIC] = 8, |
| [SND_DEVICE_IN_HDMI_MIC] = 4, |
| [SND_DEVICE_IN_BT_SCO_MIC] = 21, |
| [SND_DEVICE_IN_CAMCORDER_MIC] = 61, |
| [SND_DEVICE_IN_VOICE_DMIC_EF] = 6, |
| [SND_DEVICE_IN_VOICE_DMIC_BS] = 5, |
| [SND_DEVICE_IN_VOICE_DMIC_EF_TMUS] = 91, |
| [SND_DEVICE_IN_VOICE_SPEAKER_DMIC_EF] = 13, |
| [SND_DEVICE_IN_VOICE_SPEAKER_DMIC_BS] = 12, |
| [SND_DEVICE_IN_VOICE_TTY_FULL_HEADSET_MIC] = 16, |
| [SND_DEVICE_IN_VOICE_TTY_VCO_HANDSET_MIC] = 36, |
| [SND_DEVICE_IN_VOICE_TTY_HCO_HEADSET_MIC] = 16, |
| [SND_DEVICE_IN_VOICE_REC_MIC] = 62, |
| [SND_DEVICE_IN_VOICE_REC_DMIC_EF] = 62, |
| [SND_DEVICE_IN_VOICE_REC_DMIC_BS] = 62, |
| /* TODO: Update with proper acdb ids */ |
| [SND_DEVICE_IN_VOICE_REC_DMIC_EF_FLUENCE] = 62, |
| [SND_DEVICE_IN_VOICE_REC_DMIC_BS_FLUENCE] = 62, |
| }; |
| |
| int edid_get_max_channels(void); |
| |
| static pthread_once_t check_op_once_ctl = PTHREAD_ONCE_INIT; |
| static bool is_tmus = false; |
| |
| static void check_operator() |
| { |
| char value[PROPERTY_VALUE_MAX]; |
| int mccmnc; |
| property_get("gsm.sim.operator.numeric",value,"0"); |
| mccmnc = atoi(value); |
| ALOGD("%s: tmus mccmnc %d", __func__, mccmnc); |
| switch(mccmnc) { |
| /* TMUS MCC(310), MNC(490, 260, 026) */ |
| case 310490: |
| case 310260: |
| case 310026: |
| is_tmus = true; |
| break; |
| } |
| } |
| |
| static bool is_operator_tmus() |
| { |
| pthread_once(&check_op_once_ctl, check_operator); |
| return is_tmus; |
| } |
| |
| static int get_pcm_device_id(struct audio_route *ar, |
| audio_usecase_t usecase, |
| int device_type) |
| { |
| int device_id; |
| if (device_type == PCM_PLAYBACK) |
| device_id = pcm_device_table[usecase][0]; |
| else |
| device_id = pcm_device_table[usecase][1]; |
| return device_id; |
| } |
| |
| static int get_acdb_device_id(snd_device_t snd_device) |
| { |
| return acdb_device_table[snd_device]; |
| } |
| |
| static void add_backend_name(char *mixer_path, |
| snd_device_t snd_device) |
| { |
| if (snd_device == SND_DEVICE_IN_BT_SCO_MIC) |
| strcat(mixer_path, " bt-sco"); |
| else if(snd_device == SND_DEVICE_OUT_BT_SCO) |
| strcat(mixer_path, " bt-sco"); |
| else if (snd_device == SND_DEVICE_OUT_HDMI) |
| strcat(mixer_path, " hdmi"); |
| else if (snd_device == SND_DEVICE_OUT_SPEAKER_AND_HDMI) |
| strcat(mixer_path, " speaker-and-hdmi"); |
| } |
| |
| static int enable_audio_route(struct audio_device *adev, |
| struct audio_usecase *usecase, |
| bool update_mixer) |
| { |
| snd_device_t snd_device; |
| char mixer_path[50]; |
| |
| if (usecase == NULL) |
| return -EINVAL; |
| |
| ALOGV("%s: enter: usecase(%d)", __func__, usecase->id); |
| |
| if (usecase->type == PCM_CAPTURE) |
| snd_device = usecase->in_snd_device; |
| else |
| snd_device = usecase->out_snd_device; |
| |
| strcpy(mixer_path, use_case_table[usecase->id]); |
| add_backend_name(mixer_path, snd_device); |
| ALOGD("%s: apply mixer path: %s", __func__, mixer_path); |
| audio_route_apply_path(adev->audio_route, mixer_path); |
| if (update_mixer) |
| audio_route_update_mixer(adev->audio_route); |
| |
| ALOGV("%s: exit", __func__); |
| return 0; |
| } |
| |
| static int disable_audio_route(struct audio_device *adev, |
| struct audio_usecase *usecase, |
| bool update_mixer) |
| { |
| snd_device_t snd_device; |
| char mixer_path[50]; |
| |
| if (usecase == NULL) |
| return -EINVAL; |
| |
| ALOGV("%s: enter: usecase(%d)", __func__, usecase->id); |
| if (usecase->type == PCM_CAPTURE) |
| snd_device = usecase->in_snd_device; |
| else |
| snd_device = usecase->out_snd_device; |
| strcpy(mixer_path, use_case_table[usecase->id]); |
| add_backend_name(mixer_path, snd_device); |
| ALOGD("%s: reset mixer path: %s", __func__, mixer_path); |
| audio_route_reset_path(adev->audio_route, mixer_path); |
| if (update_mixer) |
| audio_route_update_mixer(adev->audio_route); |
| |
| ALOGV("%s: exit", __func__); |
| return 0; |
| } |
| |
| static int enable_snd_device(struct audio_device *adev, |
| snd_device_t snd_device, |
| bool update_mixer) |
| { |
| int acdb_dev_id, acdb_dev_type; |
| |
| if (snd_device < SND_DEVICE_MIN || |
| snd_device >= SND_DEVICE_MAX) { |
| ALOGE("%s: Invalid sound device %d", __func__, snd_device); |
| return -EINVAL; |
| } |
| |
| adev->snd_dev_ref_cnt[snd_device]++; |
| if (adev->snd_dev_ref_cnt[snd_device] > 1) { |
| ALOGD("%s: snd_device(%d: %s) is already active", |
| __func__, snd_device, device_table[snd_device]); |
| return 0; |
| } |
| |
| acdb_dev_id = get_acdb_device_id(snd_device); |
| if (acdb_dev_id < 0) { |
| ALOGE("%s: Could not find acdb id for device(%d)", |
| __func__, snd_device); |
| adev->snd_dev_ref_cnt[snd_device]--; |
| return -EINVAL; |
| } |
| if (adev->acdb_send_audio_cal) { |
| ALOGV("%s: sending audio calibration for snd_device(%d) acdb_id(%d)", |
| __func__, snd_device, acdb_dev_id); |
| if (snd_device >= SND_DEVICE_OUT_BEGIN && |
| snd_device < SND_DEVICE_OUT_END) |
| acdb_dev_type = ACDB_DEV_TYPE_OUT; |
| else |
| acdb_dev_type = ACDB_DEV_TYPE_IN; |
| adev->acdb_send_audio_cal(acdb_dev_id, acdb_dev_type); |
| } else { |
| ALOGW("%s: Could find the symbol acdb_send_audio_cal from %s", |
| __func__, LIB_ACDB_LOADER); |
| } |
| |
| ALOGD("%s: snd_device(%d: %s)", __func__, |
| snd_device, device_table[snd_device]); |
| audio_route_apply_path(adev->audio_route, device_table[snd_device]); |
| if (update_mixer) |
| audio_route_update_mixer(adev->audio_route); |
| |
| return 0; |
| } |
| |
| static int disable_snd_device(struct audio_device *adev, |
| snd_device_t snd_device, |
| bool update_mixer) |
| { |
| if (snd_device < SND_DEVICE_MIN || |
| snd_device >= SND_DEVICE_MAX) { |
| ALOGE("%s: Invalid sound device %d", __func__, snd_device); |
| return -EINVAL; |
| } |
| if (adev->snd_dev_ref_cnt[snd_device] <= 0) { |
| ALOGE("%s: device ref cnt is already 0", __func__); |
| return -EINVAL; |
| } |
| adev->snd_dev_ref_cnt[snd_device]--; |
| if (adev->snd_dev_ref_cnt[snd_device] == 0) { |
| ALOGD("%s: snd_device(%d: %s)", __func__, |
| snd_device, device_table[snd_device]); |
| audio_route_reset_path(adev->audio_route, device_table[snd_device]); |
| if (update_mixer) |
| audio_route_update_mixer(adev->audio_route); |
| } |
| return 0; |
| } |
| |
| static void check_usecases_codec_backend(struct audio_device *adev, |
| struct audio_usecase *uc_info, |
| snd_device_t snd_device) |
| { |
| struct listnode *node; |
| struct audio_usecase *usecase; |
| bool switch_device[AUDIO_USECASE_MAX]; |
| int i, num_uc_to_switch = 0; |
| |
| /* |
| * This function is to make sure that all the usecases that are active on |
| * the hardware codec backend are always routed to any one device that is |
| * handled by the hardware codec. |
| * For example, if low-latency and deep-buffer usecases are currently active |
| * on speaker and out_set_parameters(headset) is received on low-latency |
| * output, then we have to make sure deep-buffer is also switched to headset, |
| * because of the limitation that both the devices cannot be enabled |
| * at the same time as they share the same backend. |
| */ |
| /* Disable all the usecases on the shared backend other than the |
| specified usecase */ |
| for (i = 0; i < AUDIO_USECASE_MAX; i++) |
| switch_device[i] = false; |
| |
| list_for_each(node, &adev->usecase_list) { |
| usecase = node_to_item(node, struct audio_usecase, list); |
| if (usecase->type != PCM_CAPTURE && |
| usecase != uc_info && |
| usecase->out_snd_device != snd_device && |
| usecase->devices & AUDIO_DEVICE_OUT_ALL_CODEC_BACKEND) { |
| ALOGV("%s: Usecase (%s) is active on (%s) - disabling ..", |
| __func__, use_case_table[usecase->id], |
| device_table[usecase->out_snd_device]); |
| disable_audio_route(adev, usecase, false); |
| switch_device[usecase->id] = true; |
| num_uc_to_switch++; |
| } |
| } |
| |
| if (num_uc_to_switch) { |
| /* Make sure all the streams are de-routed before disabling the device */ |
| audio_route_update_mixer(adev->audio_route); |
| |
| list_for_each(node, &adev->usecase_list) { |
| usecase = node_to_item(node, struct audio_usecase, list); |
| if (switch_device[usecase->id]) { |
| disable_snd_device(adev, usecase->out_snd_device, false); |
| enable_snd_device(adev, snd_device, false); |
| } |
| } |
| |
| /* Make sure new snd device is enabled before re-routing the streams */ |
| audio_route_update_mixer(adev->audio_route); |
| |
| /* Re-route all the usecases on the shared backend other than the |
| specified usecase to new snd devices */ |
| list_for_each(node, &adev->usecase_list) { |
| usecase = node_to_item(node, struct audio_usecase, list); |
| /* Update the out_snd_device only before enabling the audio route */ |
| if (switch_device[usecase->id] ) { |
| usecase->out_snd_device = snd_device; |
| enable_audio_route(adev, usecase, false); |
| } |
| } |
| |
| audio_route_update_mixer(adev->audio_route); |
| } |
| } |
| |
| static int set_hdmi_channels(struct mixer *mixer, |
| int channel_count) |
| { |
| struct mixer_ctl *ctl; |
| const char *channel_cnt_str = NULL; |
| const char *mixer_ctl_name = "HDMI_RX Channels"; |
| switch (channel_count) { |
| case 8: |
| channel_cnt_str = "Eight"; break; |
| case 7: |
| channel_cnt_str = "Seven"; break; |
| case 6: |
| channel_cnt_str = "Six"; break; |
| case 5: |
| channel_cnt_str = "Five"; break; |
| case 4: |
| channel_cnt_str = "Four"; break; |
| case 3: |
| channel_cnt_str = "Three"; break; |
| default: |
| channel_cnt_str = "Two"; break; |
| } |
| ctl = mixer_get_ctl_by_name(mixer, mixer_ctl_name); |
| if (!ctl) { |
| ALOGE("%s: Could not get ctl for mixer cmd - %s", |
| __func__, mixer_ctl_name); |
| return -EINVAL; |
| } |
| ALOGV("HDMI channel count: %s", channel_cnt_str); |
| mixer_ctl_set_enum_by_string(ctl, channel_cnt_str); |
| return 0; |
| } |
| |
| /* must be called with hw device mutex locked */ |
| static void read_hdmi_channel_masks(struct stream_out *out) |
| { |
| int channels = edid_get_max_channels(); |
| ALOGV("%s: enter", __func__); |
| |
| switch (channels) { |
| /* |
| * Do not handle stereo output in Multi-channel cases |
| * Stereo case is handled in normal playback path |
| */ |
| case 6: |
| ALOGV("%s: HDMI supports 5.1", __func__); |
| out->supported_channel_masks[0] = AUDIO_CHANNEL_OUT_5POINT1; |
| break; |
| case 8: |
| ALOGV("%s: HDMI supports 5.1 and 7.1 channels", __func__); |
| out->supported_channel_masks[0] = AUDIO_CHANNEL_OUT_5POINT1; |
| out->supported_channel_masks[1] = AUDIO_CHANNEL_OUT_7POINT1; |
| break; |
| default: |
| ALOGE("Unsupported number of channels (%d)", channels); |
| break; |
| } |
| |
| ALOGV("%s: exit", __func__); |
| } |
| |
| static snd_device_t get_output_snd_device(struct audio_device *adev, |
| audio_devices_t devices) |
| { |
| audio_mode_t mode = adev->mode; |
| snd_device_t snd_device = SND_DEVICE_NONE; |
| |
| ALOGV("%s: enter: output devices(%#x)", __func__, devices); |
| if (devices == AUDIO_DEVICE_NONE || |
| devices & AUDIO_DEVICE_BIT_IN) { |
| ALOGV("%s: Invalid output devices (%#x)", __func__, devices); |
| goto exit; |
| } |
| |
| if (mode == AUDIO_MODE_IN_CALL) { |
| if (devices & AUDIO_DEVICE_OUT_WIRED_HEADPHONE || |
| devices & AUDIO_DEVICE_OUT_WIRED_HEADSET) { |
| if (adev->tty_mode == TTY_MODE_FULL) |
| snd_device = SND_DEVICE_OUT_VOICE_TTY_FULL_HEADPHONES; |
| else if (adev->tty_mode == TTY_MODE_VCO) |
| snd_device = SND_DEVICE_OUT_VOICE_TTY_VCO_HEADPHONES; |
| else if (adev->tty_mode == TTY_MODE_HCO) |
| snd_device = SND_DEVICE_OUT_VOICE_TTY_HCO_HANDSET; |
| else |
| snd_device = SND_DEVICE_OUT_VOICE_HEADPHONES; |
| } else if (devices & AUDIO_DEVICE_OUT_ALL_SCO) { |
| snd_device = SND_DEVICE_OUT_BT_SCO; |
| } else if (devices & AUDIO_DEVICE_OUT_SPEAKER) { |
| snd_device = SND_DEVICE_OUT_VOICE_SPEAKER; |
| } else if (devices & AUDIO_DEVICE_OUT_EARPIECE) { |
| if (is_operator_tmus()) |
| snd_device = SND_DEVICE_OUT_VOICE_HANDSET_TMUS; |
| else |
| snd_device = SND_DEVICE_OUT_HANDSET; |
| } |
| if (snd_device != SND_DEVICE_NONE) { |
| goto exit; |
| } |
| } |
| |
| if (popcount(devices) == 2) { |
| if (devices == (AUDIO_DEVICE_OUT_WIRED_HEADPHONE | |
| AUDIO_DEVICE_OUT_SPEAKER)) { |
| snd_device = SND_DEVICE_OUT_SPEAKER_AND_HEADPHONES; |
| } else if (devices == (AUDIO_DEVICE_OUT_WIRED_HEADSET | |
| AUDIO_DEVICE_OUT_SPEAKER)) { |
| snd_device = SND_DEVICE_OUT_SPEAKER_AND_HEADPHONES; |
| } else if (devices == (AUDIO_DEVICE_OUT_AUX_DIGITAL | |
| AUDIO_DEVICE_OUT_SPEAKER)) { |
| snd_device = SND_DEVICE_OUT_SPEAKER_AND_HDMI; |
| } else { |
| ALOGE("%s: Invalid combo device(%#x)", __func__, devices); |
| goto exit; |
| } |
| if (snd_device != SND_DEVICE_NONE) { |
| goto exit; |
| } |
| } |
| |
| if (popcount(devices) != 1) { |
| ALOGE("%s: Invalid output devices(%#x)", __func__, devices); |
| goto exit; |
| } |
| |
| if (devices & AUDIO_DEVICE_OUT_WIRED_HEADPHONE || |
| devices & AUDIO_DEVICE_OUT_WIRED_HEADSET) { |
| snd_device = SND_DEVICE_OUT_HEADPHONES; |
| } else if (devices & AUDIO_DEVICE_OUT_SPEAKER) { |
| snd_device = SND_DEVICE_OUT_SPEAKER; |
| } else if (devices & AUDIO_DEVICE_OUT_ALL_SCO) { |
| snd_device = SND_DEVICE_OUT_BT_SCO; |
| } else if (devices & AUDIO_DEVICE_OUT_AUX_DIGITAL) { |
| snd_device = SND_DEVICE_OUT_HDMI ; |
| } else if (devices & AUDIO_DEVICE_OUT_EARPIECE) { |
| snd_device = SND_DEVICE_OUT_HANDSET; |
| } else { |
| ALOGE("%s: Unknown device(s) %#x", __func__, devices); |
| } |
| exit: |
| ALOGV("%s: exit: snd_device(%s)", __func__, device_table[snd_device]); |
| return snd_device; |
| } |
| |
| static snd_device_t get_input_snd_device(struct audio_device *adev, |
| audio_devices_t out_device) |
| { |
| audio_source_t source = (adev->active_input == NULL) ? |
| AUDIO_SOURCE_DEFAULT : adev->active_input->source; |
| |
| audio_mode_t mode = adev->mode; |
| audio_devices_t in_device = ((adev->active_input == NULL) ? |
| AUDIO_DEVICE_NONE : adev->active_input->device) |
| & ~AUDIO_DEVICE_BIT_IN; |
| audio_channel_mask_t channel_mask = (adev->active_input == NULL) ? |
| AUDIO_CHANNEL_IN_MONO : adev->active_input->channel_mask; |
| snd_device_t snd_device = SND_DEVICE_NONE; |
| |
| ALOGV("%s: enter: out_device(%#x) in_device(%#x)", |
| __func__, out_device, in_device); |
| if (mode == AUDIO_MODE_IN_CALL) { |
| if (out_device == AUDIO_DEVICE_NONE) { |
| ALOGE("%s: No output device set for voice call", __func__); |
| goto exit; |
| } |
| if (adev->tty_mode != TTY_MODE_OFF) { |
| if (out_device & AUDIO_DEVICE_OUT_WIRED_HEADPHONE || |
| out_device & AUDIO_DEVICE_OUT_WIRED_HEADSET) { |
| switch (adev->tty_mode) { |
| case TTY_MODE_FULL: |
| snd_device = SND_DEVICE_IN_VOICE_TTY_FULL_HEADSET_MIC; |
| break; |
| case TTY_MODE_VCO: |
| snd_device = SND_DEVICE_IN_VOICE_TTY_VCO_HANDSET_MIC; |
| break; |
| case TTY_MODE_HCO: |
| snd_device = SND_DEVICE_IN_VOICE_TTY_HCO_HEADSET_MIC; |
| break; |
| default: |
| ALOGE("%s: Invalid TTY mode (%#x)", __func__, adev->tty_mode); |
| } |
| goto exit; |
| } |
| } |
| if (out_device & AUDIO_DEVICE_OUT_EARPIECE || |
| out_device & AUDIO_DEVICE_OUT_WIRED_HEADPHONE) { |
| if (adev->mic_type_analog || adev->fluence_in_voice_call == false) { |
| snd_device = SND_DEVICE_IN_HANDSET_MIC; |
| } else { |
| if (adev->dualmic_config == DUALMIC_CONFIG_ENDFIRE) { |
| if (is_operator_tmus()) |
| snd_device = SND_DEVICE_IN_VOICE_DMIC_EF_TMUS; |
| else |
| snd_device = SND_DEVICE_IN_VOICE_DMIC_EF; |
| } else if(adev->dualmic_config == DUALMIC_CONFIG_BROADSIDE) |
| snd_device = SND_DEVICE_IN_VOICE_DMIC_BS; |
| else |
| snd_device = SND_DEVICE_IN_HANDSET_MIC; |
| } |
| } else if (out_device & AUDIO_DEVICE_OUT_WIRED_HEADSET) { |
| snd_device = SND_DEVICE_IN_VOICE_HEADSET_MIC; |
| } else if (out_device & AUDIO_DEVICE_OUT_ALL_SCO) { |
| snd_device = SND_DEVICE_IN_BT_SCO_MIC ; |
| } else if (out_device & AUDIO_DEVICE_OUT_SPEAKER) { |
| if (adev->fluence_in_voice_call && adev->fluence_in_spkr_mode && |
| adev->dualmic_config == DUALMIC_CONFIG_ENDFIRE) { |
| snd_device = SND_DEVICE_IN_VOICE_SPEAKER_DMIC_EF; |
| } else if (adev->fluence_in_voice_call && adev->fluence_in_spkr_mode && |
| adev->dualmic_config == DUALMIC_CONFIG_BROADSIDE) { |
| snd_device = SND_DEVICE_IN_VOICE_SPEAKER_DMIC_BS; |
| } else { |
| snd_device = SND_DEVICE_IN_VOICE_SPEAKER_MIC; |
| } |
| } |
| } else if (source == AUDIO_SOURCE_CAMCORDER) { |
| if (in_device & AUDIO_DEVICE_IN_BUILTIN_MIC || |
| in_device & AUDIO_DEVICE_IN_BACK_MIC) { |
| snd_device = SND_DEVICE_IN_CAMCORDER_MIC; |
| } |
| } else if (source == AUDIO_SOURCE_VOICE_RECOGNITION) { |
| if (in_device & AUDIO_DEVICE_IN_BUILTIN_MIC) { |
| if (adev->dualmic_config == DUALMIC_CONFIG_ENDFIRE) { |
| if (channel_mask == AUDIO_CHANNEL_IN_FRONT_BACK) |
| snd_device = SND_DEVICE_IN_VOICE_REC_DMIC_EF; |
| else if (adev->fluence_in_voice_rec) |
| snd_device = SND_DEVICE_IN_VOICE_REC_DMIC_EF_FLUENCE; |
| else |
| snd_device = SND_DEVICE_IN_VOICE_REC_MIC; |
| } else if (adev->dualmic_config == DUALMIC_CONFIG_BROADSIDE) { |
| if (channel_mask == AUDIO_CHANNEL_IN_FRONT_BACK) |
| snd_device = SND_DEVICE_IN_VOICE_REC_DMIC_BS; |
| else if (adev->fluence_in_voice_rec) |
| snd_device = SND_DEVICE_IN_VOICE_REC_DMIC_BS_FLUENCE; |
| else |
| snd_device = SND_DEVICE_IN_VOICE_REC_MIC; |
| } else |
| snd_device = SND_DEVICE_IN_VOICE_REC_MIC; |
| } |
| } else if (source == AUDIO_SOURCE_VOICE_COMMUNICATION) { |
| if (out_device & AUDIO_DEVICE_OUT_SPEAKER) |
| in_device = AUDIO_DEVICE_IN_BACK_MIC; |
| } else if (source == AUDIO_SOURCE_DEFAULT) { |
| goto exit; |
| } |
| |
| if (snd_device != SND_DEVICE_NONE) { |
| goto exit; |
| } |
| |
| if (in_device != AUDIO_DEVICE_NONE && |
| !(in_device & AUDIO_DEVICE_IN_VOICE_CALL) && |
| !(in_device & AUDIO_DEVICE_IN_COMMUNICATION)) { |
| if (in_device & AUDIO_DEVICE_IN_BUILTIN_MIC) { |
| snd_device = SND_DEVICE_IN_HANDSET_MIC; |
| } else if (in_device & AUDIO_DEVICE_IN_BACK_MIC) { |
| if (adev->mic_type_analog) |
| snd_device = SND_DEVICE_IN_HANDSET_MIC; |
| else |
| snd_device = SND_DEVICE_IN_SPEAKER_MIC; |
| } else if (in_device & AUDIO_DEVICE_IN_WIRED_HEADSET) { |
| snd_device = SND_DEVICE_IN_HEADSET_MIC; |
| } else if (in_device & AUDIO_DEVICE_IN_BLUETOOTH_SCO_HEADSET) { |
| snd_device = SND_DEVICE_IN_BT_SCO_MIC ; |
| } else if (in_device & AUDIO_DEVICE_IN_AUX_DIGITAL) { |
| snd_device = SND_DEVICE_IN_HDMI_MIC; |
| } else { |
| ALOGE("%s: Unknown input device(s) %#x", __func__, in_device); |
| ALOGW("%s: Using default handset-mic", __func__); |
| snd_device = SND_DEVICE_IN_HANDSET_MIC; |
| } |
| } else { |
| if (out_device & AUDIO_DEVICE_OUT_EARPIECE) { |
| snd_device = SND_DEVICE_IN_HANDSET_MIC; |
| } else if (out_device & AUDIO_DEVICE_OUT_WIRED_HEADSET) { |
| snd_device = SND_DEVICE_IN_HEADSET_MIC; |
| } else if (out_device & AUDIO_DEVICE_OUT_SPEAKER) { |
| snd_device = SND_DEVICE_IN_SPEAKER_MIC; |
| } else if (out_device & AUDIO_DEVICE_OUT_WIRED_HEADPHONE) { |
| snd_device = SND_DEVICE_IN_HANDSET_MIC; |
| } else if (out_device & AUDIO_DEVICE_OUT_BLUETOOTH_SCO_HEADSET) { |
| snd_device = SND_DEVICE_IN_BT_SCO_MIC; |
| } else if (out_device & AUDIO_DEVICE_OUT_AUX_DIGITAL) { |
| snd_device = SND_DEVICE_IN_HDMI_MIC; |
| } else { |
| ALOGE("%s: Unknown output device(s) %#x", __func__, out_device); |
| ALOGW("%s: Using default handset-mic", __func__); |
| snd_device = SND_DEVICE_IN_HANDSET_MIC; |
| } |
| } |
| exit: |
| ALOGV("%s: exit: in_snd_device(%s)", __func__, device_table[snd_device]); |
| return snd_device; |
| } |
| |
| static struct audio_usecase *get_usecase_from_list(struct audio_device *adev, |
| audio_usecase_t uc_id) |
| { |
| struct audio_usecase *usecase; |
| struct listnode *node; |
| |
| list_for_each(node, &adev->usecase_list) { |
| usecase = node_to_item(node, struct audio_usecase, list); |
| if (usecase->id == uc_id) |
| return usecase; |
| } |
| return NULL; |
| } |
| |
| static int select_devices(struct audio_device *adev, |
| audio_usecase_t uc_id) |
| { |
| snd_device_t out_snd_device = SND_DEVICE_NONE; |
| snd_device_t in_snd_device = SND_DEVICE_NONE; |
| struct audio_usecase *usecase = NULL; |
| struct audio_usecase *vc_usecase = NULL; |
| struct listnode *node; |
| int acdb_rx_id, acdb_tx_id; |
| int status = 0; |
| |
| usecase = get_usecase_from_list(adev, uc_id); |
| if (usecase == NULL) { |
| ALOGE("%s: Could not find the usecase(%d)", __func__, uc_id); |
| return -EINVAL; |
| } |
| |
| if (usecase->type == VOICE_CALL) { |
| out_snd_device = get_output_snd_device(adev, usecase->stream.out->devices); |
| in_snd_device = get_input_snd_device(adev, usecase->stream.out->devices); |
| usecase->devices = usecase->stream.out->devices; |
| } else { |
| /* |
| * If the voice call is active, use the sound devices of voice call usecase |
| * so that it would not result any device switch. All the usecases will |
| * be switched to new device when select_devices() is called for voice call |
| * usecase. This is to avoid switching devices for voice call when |
| * check_usecases_codec_backend() is called below. |
| */ |
| if (adev->in_call) { |
| vc_usecase = get_usecase_from_list(adev, USECASE_VOICE_CALL); |
| if (vc_usecase->devices & AUDIO_DEVICE_OUT_ALL_CODEC_BACKEND) { |
| in_snd_device = vc_usecase->in_snd_device; |
| out_snd_device = vc_usecase->out_snd_device; |
| } |
| } |
| if (usecase->type == PCM_PLAYBACK) { |
| usecase->devices = usecase->stream.out->devices; |
| in_snd_device = SND_DEVICE_NONE; |
| if (out_snd_device == SND_DEVICE_NONE) |
| out_snd_device = get_output_snd_device(adev, |
| usecase->stream.out->devices); |
| } else if (usecase->type == PCM_CAPTURE) { |
| usecase->devices = usecase->stream.in->device; |
| out_snd_device = SND_DEVICE_NONE; |
| if (in_snd_device == SND_DEVICE_NONE) |
| in_snd_device = get_input_snd_device(adev, SND_DEVICE_NONE); |
| } |
| } |
| |
| if (out_snd_device == usecase->out_snd_device && |
| in_snd_device == usecase->in_snd_device) { |
| return 0; |
| } |
| |
| ALOGD("%s: out_snd_device(%d: %s) in_snd_device(%d: %s)", __func__, |
| out_snd_device, device_table[out_snd_device], |
| in_snd_device, device_table[in_snd_device]); |
| |
| /* |
| * Limitation: While in call, to do a device switch we need to disable |
| * and enable both RX and TX devices though one of them is same as current |
| * device. |
| */ |
| if (usecase->type == VOICE_CALL && adev->csd_client != NULL && |
| usecase->in_snd_device != SND_DEVICE_NONE && |
| usecase->out_snd_device != SND_DEVICE_NONE) { |
| /* This must be called before disabling the mixer controls on APQ side */ |
| if (adev->csd_disable_device == NULL) { |
| ALOGE("%s: dlsym error for csd_client_disable_device", __func__); |
| } else { |
| status = adev->csd_disable_device(); |
| if (status < 0) { |
| ALOGE("%s: csd_client_disable_device, failed, error %d", |
| __func__, status); |
| } |
| } |
| } |
| |
| /* Disable current sound devices */ |
| if (usecase->out_snd_device != SND_DEVICE_NONE) { |
| disable_audio_route(adev, usecase, true); |
| disable_snd_device(adev, usecase->out_snd_device, false); |
| } |
| |
| if (usecase->in_snd_device != SND_DEVICE_NONE) { |
| disable_audio_route(adev, usecase, true); |
| disable_snd_device(adev, usecase->in_snd_device, false); |
| } |
| |
| /* Enable new sound devices */ |
| if (out_snd_device != SND_DEVICE_NONE) { |
| if (usecase->devices & AUDIO_DEVICE_OUT_ALL_CODEC_BACKEND) |
| check_usecases_codec_backend(adev, usecase, out_snd_device); |
| enable_snd_device(adev, out_snd_device, false); |
| } |
| |
| if (in_snd_device != SND_DEVICE_NONE) |
| enable_snd_device(adev, in_snd_device, false); |
| |
| audio_route_update_mixer(adev->audio_route); |
| |
| usecase->in_snd_device = in_snd_device; |
| usecase->out_snd_device = out_snd_device; |
| |
| enable_audio_route(adev, usecase, true); |
| |
| if (usecase->type == VOICE_CALL && adev->csd_client) { |
| if (adev->csd_enable_device == NULL) { |
| ALOGE("%s: dlsym error for csd_client_enable_device", |
| __func__); |
| } else { |
| acdb_rx_id = get_acdb_device_id(out_snd_device); |
| acdb_tx_id = get_acdb_device_id(in_snd_device); |
| |
| if (acdb_rx_id > 0 || acdb_tx_id > 0) { |
| status = adev->csd_enable_device(acdb_rx_id, acdb_tx_id, |
| adev->acdb_settings); |
| if (status < 0) { |
| ALOGE("%s: csd_client_enable_device, failed, error %d", |
| __func__, status); |
| } |
| } else { |
| ALOGE("%s: Incorrect ACDB IDs (rx: %d tx: %d)", __func__, |
| acdb_rx_id, acdb_tx_id); |
| } |
| } |
| } |
| |
| return status; |
| } |
| |
| static int stop_input_stream(struct stream_in *in) |
| { |
| int i, ret = 0; |
| struct audio_usecase *uc_info; |
| struct audio_device *adev = in->dev; |
| |
| adev->active_input = NULL; |
| |
| ALOGD("%s: enter: usecase(%d: %s)", __func__, |
| in->usecase, use_case_table[in->usecase]); |
| uc_info = get_usecase_from_list(adev, in->usecase); |
| if (uc_info == NULL) { |
| ALOGE("%s: Could not find the usecase (%d) in the list", |
| __func__, in->usecase); |
| return -EINVAL; |
| } |
| |
| /* 1. Disable stream specific mixer controls */ |
| disable_audio_route(adev, uc_info, true); |
| |
| /* 2. Disable the tx device */ |
| disable_snd_device(adev, uc_info->in_snd_device, true); |
| |
| list_remove(&uc_info->list); |
| free(uc_info); |
| |
| ALOGD("%s: exit: status(%d)", __func__, ret); |
| return ret; |
| } |
| |
| int start_input_stream(struct stream_in *in) |
| { |
| /* 1. Enable output device and stream routing controls */ |
| int ret = 0; |
| struct audio_usecase *uc_info; |
| struct audio_device *adev = in->dev; |
| |
| ALOGD("%s: enter: usecase(%d)", __func__, in->usecase); |
| in->pcm_device_id = get_pcm_device_id(adev->audio_route, |
| in->usecase, |
| PCM_CAPTURE); |
| if (in->pcm_device_id < 0) { |
| ALOGE("%s: Could not find PCM device id for the usecase(%d)", |
| __func__, in->usecase); |
| ret = -EINVAL; |
| goto error_config; |
| } |
| |
| adev->active_input = in; |
| uc_info = (struct audio_usecase *)calloc(1, sizeof(struct audio_usecase)); |
| uc_info->id = in->usecase; |
| uc_info->type = PCM_CAPTURE; |
| uc_info->stream.in = in; |
| uc_info->devices = in->device; |
| uc_info->in_snd_device = SND_DEVICE_NONE; |
| uc_info->out_snd_device = SND_DEVICE_NONE; |
| |
| list_add_tail(&adev->usecase_list, &uc_info->list); |
| select_devices(adev, in->usecase); |
| |
| ALOGV("%s: Opening PCM device card_id(%d) device_id(%d), channels %d", |
| __func__, SOUND_CARD, in->pcm_device_id, in->config.channels); |
| in->pcm = pcm_open(SOUND_CARD, in->pcm_device_id, |
| PCM_IN, &in->config); |
| if (in->pcm && !pcm_is_ready(in->pcm)) { |
| ALOGE("%s: %s", __func__, pcm_get_error(in->pcm)); |
| pcm_close(in->pcm); |
| in->pcm = NULL; |
| ret = -EIO; |
| goto error_open; |
| } |
| ALOGD("%s: exit", __func__); |
| return ret; |
| |
| error_open: |
| stop_input_stream(in); |
| |
| error_config: |
| adev->active_input = NULL; |
| ALOGD("%s: exit: status(%d)", __func__, ret); |
| |
| return ret; |
| } |
| |
| static int stop_output_stream(struct stream_out *out) |
| { |
| int i, ret = 0; |
| struct audio_usecase *uc_info; |
| struct audio_device *adev = out->dev; |
| |
| ALOGD("%s: enter: usecase(%d: %s)", __func__, |
| out->usecase, use_case_table[out->usecase]); |
| uc_info = get_usecase_from_list(adev, out->usecase); |
| if (uc_info == NULL) { |
| ALOGE("%s: Could not find the usecase (%d) in the list", |
| __func__, out->usecase); |
| return -EINVAL; |
| } |
| |
| /* 1. Get and set stream specific mixer controls */ |
| disable_audio_route(adev, uc_info, true); |
| |
| /* 2. Disable the rx device */ |
| disable_snd_device(adev, uc_info->out_snd_device, true); |
| |
| list_remove(&uc_info->list); |
| free(uc_info); |
| |
| ALOGD("%s: exit: status(%d)", __func__, ret); |
| return ret; |
| } |
| |
| int start_output_stream(struct stream_out *out) |
| { |
| int ret = 0; |
| struct audio_usecase *uc_info; |
| struct audio_device *adev = out->dev; |
| |
| ALOGD("%s: enter: usecase(%d: %s) devices(%#x)", |
| __func__, out->usecase, use_case_table[out->usecase], out->devices); |
| out->pcm_device_id = get_pcm_device_id(adev->audio_route, |
| out->usecase, |
| PCM_PLAYBACK); |
| if (out->pcm_device_id < 0) { |
| ALOGE("%s: Invalid PCM device id(%d) for the usecase(%d)", |
| __func__, out->pcm_device_id, out->usecase); |
| ret = -EINVAL; |
| goto error_config; |
| } |
| |
| uc_info = (struct audio_usecase *)calloc(1, sizeof(struct audio_usecase)); |
| uc_info->id = out->usecase; |
| uc_info->type = PCM_PLAYBACK; |
| uc_info->stream.out = out; |
| uc_info->devices = out->devices; |
| uc_info->in_snd_device = SND_DEVICE_NONE; |
| uc_info->out_snd_device = SND_DEVICE_NONE; |
| |
| list_add_tail(&adev->usecase_list, &uc_info->list); |
| |
| select_devices(adev, out->usecase); |
| |
| ALOGV("%s: Opening PCM device card_id(%d) device_id(%d)", |
| __func__, 0, out->pcm_device_id); |
| out->pcm = pcm_open(SOUND_CARD, out->pcm_device_id, |
| PCM_OUT, &out->config); |
| if (out->pcm && !pcm_is_ready(out->pcm)) { |
| ALOGE("%s: %s", __func__, pcm_get_error(out->pcm)); |
| pcm_close(out->pcm); |
| out->pcm = NULL; |
| ret = -EIO; |
| goto error_pcm_open; |
| } |
| ALOGD("%s: exit", __func__); |
| return 0; |
| error_pcm_open: |
| stop_output_stream(out); |
| error_config: |
| return ret; |
| } |
| |
| static int stop_voice_call(struct audio_device *adev) |
| { |
| int i, ret = 0; |
| struct audio_usecase *uc_info; |
| |
| ALOGD("%s: enter", __func__); |
| adev->in_call = false; |
| if (adev->csd_client) { |
| if (adev->csd_stop_voice == NULL) { |
| ALOGE("dlsym error for csd_client_disable_device"); |
| } else { |
| ret = adev->csd_stop_voice(); |
| if (ret < 0) { |
| ALOGE("%s: csd_client error %d\n", __func__, ret); |
| } |
| } |
| } |
| |
| /* 1. Close the PCM devices */ |
| if (adev->voice_call_rx) { |
| pcm_close(adev->voice_call_rx); |
| adev->voice_call_rx = NULL; |
| } |
| if (adev->voice_call_tx) { |
| pcm_close(adev->voice_call_tx); |
| adev->voice_call_tx = NULL; |
| } |
| |
| uc_info = get_usecase_from_list(adev, USECASE_VOICE_CALL); |
| if (uc_info == NULL) { |
| ALOGE("%s: Could not find the usecase (%d) in the list", |
| __func__, USECASE_VOICE_CALL); |
| return -EINVAL; |
| } |
| |
| /* 2. Get and set stream specific mixer controls */ |
| disable_audio_route(adev, uc_info, true); |
| |
| /* 3. Disable the rx and tx devices */ |
| disable_snd_device(adev, uc_info->out_snd_device, false); |
| disable_snd_device(adev, uc_info->in_snd_device, true); |
| |
| list_remove(&uc_info->list); |
| free(uc_info); |
| |
| ALOGD("%s: exit: status(%d)", __func__, ret); |
| return ret; |
| } |
| |
| static int start_voice_call(struct audio_device *adev) |
| { |
| int i, ret = 0; |
| struct audio_usecase *uc_info; |
| int pcm_dev_rx_id, pcm_dev_tx_id; |
| |
| ALOGD("%s: enter", __func__); |
| |
| uc_info = (struct audio_usecase *)calloc(1, sizeof(struct audio_usecase)); |
| uc_info->id = USECASE_VOICE_CALL; |
| uc_info->type = VOICE_CALL; |
| uc_info->stream.out = adev->primary_output; |
| uc_info->devices = adev->primary_output->devices; |
| uc_info->in_snd_device = SND_DEVICE_NONE; |
| uc_info->out_snd_device = SND_DEVICE_NONE; |
| |
| list_add_tail(&adev->usecase_list, &uc_info->list); |
| |
| select_devices(adev, USECASE_VOICE_CALL); |
| |
| pcm_dev_rx_id = get_pcm_device_id(adev->audio_route, uc_info->id, |
| PCM_PLAYBACK); |
| pcm_dev_tx_id = get_pcm_device_id(adev->audio_route, uc_info->id, |
| PCM_CAPTURE); |
| |
| if (pcm_dev_rx_id < 0 || pcm_dev_tx_id < 0) { |
| ALOGE("%s: Invalid PCM devices (rx: %d tx: %d) for the usecase(%d)", |
| __func__, pcm_dev_rx_id, pcm_dev_tx_id, uc_info->id); |
| ret = -EIO; |
| goto error_start_voice; |
| } |
| |
| ALOGV("%s: Opening PCM playback device card_id(%d) device_id(%d)", |
| __func__, SOUND_CARD, pcm_dev_rx_id); |
| adev->voice_call_rx = pcm_open(SOUND_CARD, |
| pcm_dev_rx_id, |
| PCM_OUT, &pcm_config_voice_call); |
| if (adev->voice_call_rx && !pcm_is_ready(adev->voice_call_rx)) { |
| ALOGE("%s: %s", __func__, pcm_get_error(adev->voice_call_rx)); |
| ret = -EIO; |
| goto error_start_voice; |
| } |
| |
| ALOGV("%s: Opening PCM capture device card_id(%d) device_id(%d)", |
| __func__, SOUND_CARD, pcm_dev_tx_id); |
| adev->voice_call_tx = pcm_open(SOUND_CARD, |
| pcm_dev_tx_id, |
| PCM_IN, &pcm_config_voice_call); |
| if (adev->voice_call_tx && !pcm_is_ready(adev->voice_call_tx)) { |
| ALOGE("%s: %s", __func__, pcm_get_error(adev->voice_call_tx)); |
| ret = -EIO; |
| goto error_start_voice; |
| } |
| pcm_start(adev->voice_call_rx); |
| pcm_start(adev->voice_call_tx); |
| |
| if (adev->csd_client) { |
| if (adev->csd_start_voice == NULL) { |
| ALOGE("dlsym error for csd_client_start_voice"); |
| goto error_start_voice; |
| } else { |
| ret = adev->csd_start_voice(); |
| if (ret < 0) { |
| ALOGE("%s: csd_start_voice error %d\n", __func__, ret); |
| goto error_start_voice; |
| } |
| } |
| } |
| |
| adev->in_call = true; |
| return 0; |
| |
| error_start_voice: |
| stop_voice_call(adev); |
| |
| ALOGD("%s: exit: status(%d)", __func__, ret); |
| return ret; |
| } |
| |
| static int check_input_parameters(uint32_t sample_rate, |
| audio_format_t format, |
| int channel_count) |
| { |
| if (format != AUDIO_FORMAT_PCM_16_BIT) return -EINVAL; |
| |
| if ((channel_count < 1) || (channel_count > 2)) return -EINVAL; |
| |
| switch (sample_rate) { |
| case 8000: |
| case 11025: |
| case 12000: |
| case 16000: |
| case 22050: |
| case 24000: |
| case 32000: |
| case 44100: |
| case 48000: |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static size_t get_input_buffer_size(uint32_t sample_rate, |
| audio_format_t format, |
| int channel_count) |
| { |
| size_t size = 0; |
| |
| if (check_input_parameters(sample_rate, format, channel_count) != 0) return 0; |
| |
| if (sample_rate == 8000 || sample_rate == 16000 || sample_rate == 32000) { |
| size = (sample_rate * 20) / 1000; |
| } else if (sample_rate == 11025 || sample_rate == 12000) { |
| size = 256; |
| } else if (sample_rate == 22050 || sample_rate == 24000) { |
| size = 512; |
| } else if (sample_rate == 44100 || sample_rate == 48000) { |
| size = 1024; |
| } |
| |
| return size * sizeof(short) * channel_count; |
| } |
| |
| static uint32_t out_get_sample_rate(const struct audio_stream *stream) |
| { |
| struct stream_out *out = (struct stream_out *)stream; |
| |
| return out->config.rate; |
| } |
| |
| static int out_set_sample_rate(struct audio_stream *stream, uint32_t rate) |
| { |
| return -ENOSYS; |
| } |
| |
| static size_t out_get_buffer_size(const struct audio_stream *stream) |
| { |
| struct stream_out *out = (struct stream_out *)stream; |
| |
| return out->config.period_size * audio_stream_frame_size(stream); |
| } |
| |
| static uint32_t out_get_channels(const struct audio_stream *stream) |
| { |
| struct stream_out *out = (struct stream_out *)stream; |
| |
| return out->channel_mask; |
| } |
| |
| static audio_format_t out_get_format(const struct audio_stream *stream) |
| { |
| return AUDIO_FORMAT_PCM_16_BIT; |
| } |
| |
| static int out_set_format(struct audio_stream *stream, audio_format_t format) |
| { |
| return -ENOSYS; |
| } |
| |
| static int out_standby(struct audio_stream *stream) |
| { |
| struct stream_out *out = (struct stream_out *)stream; |
| struct audio_device *adev = out->dev; |
| ALOGD("%s: enter: usecase(%d: %s)", __func__, |
| out->usecase, use_case_table[out->usecase]); |
| pthread_mutex_lock(&out->lock); |
| |
| if (!out->standby) { |
| out->standby = true; |
| if (out->pcm) { |
| pcm_close(out->pcm); |
| out->pcm = NULL; |
| } |
| pthread_mutex_lock(&adev->lock); |
| stop_output_stream(out); |
| pthread_mutex_unlock(&adev->lock); |
| } |
| pthread_mutex_unlock(&out->lock); |
| ALOGD("%s: exit", __func__); |
| return 0; |
| } |
| |
| static int out_dump(const struct audio_stream *stream, int fd) |
| { |
| return 0; |
| } |
| |
| static int out_set_parameters(struct audio_stream *stream, const char *kvpairs) |
| { |
| struct stream_out *out = (struct stream_out *)stream; |
| struct audio_device *adev = out->dev; |
| struct audio_usecase *usecase; |
| struct listnode *node; |
| struct str_parms *parms; |
| char value[32]; |
| int ret, val = 0; |
| bool select_new_device = false; |
| |
| ALOGD("%s: enter: usecase(%d: %s) kvpairs: %s", |
| __func__, out->usecase, use_case_table[out->usecase], kvpairs); |
| parms = str_parms_create_str(kvpairs); |
| ret = str_parms_get_str(parms, AUDIO_PARAMETER_STREAM_ROUTING, value, sizeof(value)); |
| if (ret >= 0) { |
| val = atoi(value); |
| pthread_mutex_lock(&out->lock); |
| pthread_mutex_lock(&adev->lock); |
| |
| /* |
| * When HDMI cable is unplugged the music playback is paused and |
| * the policy manager sends routing=0. But the audioflinger |
| * continues to write data until standby time (3sec). |
| * As the HDMI core is turned off, the write gets blocked. |
| * Avoid this by routing audio to speaker until standby. |
| */ |
| if (out->devices == AUDIO_DEVICE_OUT_AUX_DIGITAL && |
| val == AUDIO_DEVICE_NONE) { |
| val = AUDIO_DEVICE_OUT_SPEAKER; |
| } |
| |
| /* |
| * select_devices() call below switches all the usecases on the same |
| * backend to the new device. Refer to check_usecases_codec_backend() in |
| * the select_devices(). But how do we undo this? |
| * |
| * For example, music playback is active on headset (deep-buffer usecase) |
| * and if we go to ringtones and select a ringtone, low-latency usecase |
| * will be started on headset+speaker. As we can't enable headset+speaker |
| * and headset devices at the same time, select_devices() switches the music |
| * playback to headset+speaker while starting low-lateny usecase for ringtone. |
| * So when the ringtone playback is completed, how do we undo the same? |
| * |
| * We are relying on the out_set_parameters() call on deep-buffer output, |
| * once the ringtone playback is ended. |
| * NOTE: We should not check if the current devices are same as new devices. |
| * Because select_devices() must be called to switch back the music |
| * playback to headset. |
| */ |
| if (val != 0) { |
| out->devices = val; |
| |
| if (!out->standby) |
| select_devices(adev, out->usecase); |
| |
| if ((adev->mode == AUDIO_MODE_IN_CALL) && !adev->in_call && |
| (out == adev->primary_output)) { |
| start_voice_call(adev); |
| } else if ((adev->mode == AUDIO_MODE_IN_CALL) && adev->in_call && |
| (out == adev->primary_output)) { |
| select_devices(adev, USECASE_VOICE_CALL); |
| } |
| } |
| |
| if ((adev->mode != AUDIO_MODE_IN_CALL) && adev->in_call && |
| (out == adev->primary_output)) { |
| stop_voice_call(adev); |
| } |
| |
| pthread_mutex_unlock(&adev->lock); |
| pthread_mutex_unlock(&out->lock); |
| } |
| str_parms_destroy(parms); |
| ALOGD("%s: exit: code(%d)", __func__, ret); |
| return ret; |
| } |
| |
| static char* out_get_parameters(const struct audio_stream *stream, const char *keys) |
| { |
| struct stream_out *out = (struct stream_out *)stream; |
| struct str_parms *query = str_parms_create_str(keys); |
| char *str; |
| char value[256]; |
| struct str_parms *reply = str_parms_create(); |
| size_t i, j; |
| int ret; |
| bool first = true; |
| ALOGD("%s: enter: keys - %s", __func__, keys); |
| ret = str_parms_get_str(query, AUDIO_PARAMETER_STREAM_SUP_CHANNELS, value, sizeof(value)); |
| if (ret >= 0) { |
| value[0] = '\0'; |
| i = 0; |
| while (out->supported_channel_masks[i] != 0) { |
| for (j = 0; j < ARRAY_SIZE(out_channels_name_to_enum_table); j++) { |
| if (out_channels_name_to_enum_table[j].value == out->supported_channel_masks[i]) { |
| if (!first) { |
| strcat(value, "|"); |
| } |
| strcat(value, out_channels_name_to_enum_table[j].name); |
| first = false; |
| break; |
| } |
| } |
| i++; |
| } |
| str_parms_add_str(reply, AUDIO_PARAMETER_STREAM_SUP_CHANNELS, value); |
| str = str_parms_to_str(reply); |
| } else { |
| str = strdup(keys); |
| } |
| str_parms_destroy(query); |
| str_parms_destroy(reply); |
| ALOGD("%s: exit: returns - %s", __func__, str); |
| return str; |
| } |
| |
| static uint32_t out_get_latency(const struct audio_stream_out *stream) |
| { |
| struct stream_out *out = (struct stream_out *)stream; |
| |
| return (out->config.period_count * out->config.period_size * 1000) / (out->config.rate); |
| } |
| |
| static int out_set_volume(struct audio_stream_out *stream, float left, |
| float right) |
| { |
| return -ENOSYS; |
| } |
| |
| static ssize_t out_write(struct audio_stream_out *stream, const void *buffer, |
| size_t bytes) |
| { |
| struct stream_out *out = (struct stream_out *)stream; |
| struct audio_device *adev = out->dev; |
| int i, ret = -1; |
| |
| pthread_mutex_lock(&out->lock); |
| if (out->standby) { |
| pthread_mutex_lock(&adev->lock); |
| ret = start_output_stream(out); |
| pthread_mutex_unlock(&adev->lock); |
| if (ret != 0) { |
| goto exit; |
| } |
| out->standby = false; |
| } |
| |
| if (out->pcm) { |
| //ALOGV("%s: writing buffer (%d bytes) to pcm device", __func__, bytes); |
| ret = pcm_write(out->pcm, (void *)buffer, bytes); |
| } |
| |
| exit: |
| pthread_mutex_unlock(&out->lock); |
| |
| if (ret != 0) { |
| out_standby(&out->stream.common); |
| usleep(bytes * 1000000 / audio_stream_frame_size(&out->stream.common) / |
| out_get_sample_rate(&out->stream.common)); |
| } |
| return bytes; |
| } |
| |
| static int out_get_render_position(const struct audio_stream_out *stream, |
| uint32_t *dsp_frames) |
| { |
| return -EINVAL; |
| } |
| |
| static int out_add_audio_effect(const struct audio_stream *stream, effect_handle_t effect) |
| { |
| return 0; |
| } |
| |
| static int out_remove_audio_effect(const struct audio_stream *stream, effect_handle_t effect) |
| { |
| return 0; |
| } |
| |
| static int out_get_next_write_timestamp(const struct audio_stream_out *stream, |
| int64_t *timestamp) |
| { |
| return -EINVAL; |
| } |
| |
| /** audio_stream_in implementation **/ |
| static uint32_t in_get_sample_rate(const struct audio_stream *stream) |
| { |
| struct stream_in *in = (struct stream_in *)stream; |
| |
| return in->config.rate; |
| } |
| |
| static int in_set_sample_rate(struct audio_stream *stream, uint32_t rate) |
| { |
| return -ENOSYS; |
| } |
| |
| static size_t in_get_buffer_size(const struct audio_stream *stream) |
| { |
| struct stream_in *in = (struct stream_in *)stream; |
| |
| return in->config.period_size * audio_stream_frame_size(stream); |
| } |
| |
| static uint32_t in_get_channels(const struct audio_stream *stream) |
| { |
| struct stream_in *in = (struct stream_in *)stream; |
| |
| return in->channel_mask; |
| } |
| |
| static audio_format_t in_get_format(const struct audio_stream *stream) |
| { |
| return AUDIO_FORMAT_PCM_16_BIT; |
| } |
| |
| static int in_set_format(struct audio_stream *stream, audio_format_t format) |
| { |
| return -ENOSYS; |
| } |
| |
| static int in_standby(struct audio_stream *stream) |
| { |
| struct stream_in *in = (struct stream_in *)stream; |
| struct audio_device *adev = in->dev; |
| int status = 0; |
| ALOGD("%s: enter", __func__); |
| pthread_mutex_lock(&in->lock); |
| if (!in->standby) { |
| in->standby = true; |
| if (in->pcm) { |
| pcm_close(in->pcm); |
| in->pcm = NULL; |
| } |
| pthread_mutex_lock(&adev->lock); |
| status = stop_input_stream(in); |
| pthread_mutex_unlock(&adev->lock); |
| } |
| pthread_mutex_unlock(&in->lock); |
| ALOGD("%s: exit: status(%d)", __func__, status); |
| return status; |
| } |
| |
| static int in_dump(const struct audio_stream *stream, int fd) |
| { |
| return 0; |
| } |
| |
| static int in_set_parameters(struct audio_stream *stream, const char *kvpairs) |
| { |
| struct stream_in *in = (struct stream_in *)stream; |
| struct audio_device *adev = in->dev; |
| struct str_parms *parms; |
| char *str; |
| char value[32]; |
| int ret, val = 0; |
| |
| ALOGD("%s: enter: kvpairs=%s", __func__, kvpairs); |
| parms = str_parms_create_str(kvpairs); |
| |
| ret = str_parms_get_str(parms, AUDIO_PARAMETER_STREAM_INPUT_SOURCE, value, sizeof(value)); |
| |
| pthread_mutex_lock(&in->lock); |
| pthread_mutex_lock(&adev->lock); |
| if (ret >= 0) { |
| val = atoi(value); |
| /* no audio source uses val == 0 */ |
| if ((in->source != val) && (val != 0)) { |
| in->source = val; |
| } |
| } |
| |
| ret = str_parms_get_str(parms, AUDIO_PARAMETER_STREAM_ROUTING, value, sizeof(value)); |
| if (ret >= 0) { |
| val = atoi(value); |
| if ((in->device != val) && (val != 0)) { |
| in->device = val; |
| /* If recording is in progress, change the tx device to new device */ |
| if (!in->standby) |
| ret = select_devices(adev, in->usecase); |
| } |
| } |
| |
| pthread_mutex_unlock(&adev->lock); |
| pthread_mutex_unlock(&in->lock); |
| |
| str_parms_destroy(parms); |
| ALOGD("%s: exit: status(%d)", __func__, ret); |
| return ret; |
| } |
| |
| static char* in_get_parameters(const struct audio_stream *stream, |
| const char *keys) |
| { |
| return strdup(""); |
| } |
| |
| static int in_set_gain(struct audio_stream_in *stream, float gain) |
| { |
| return 0; |
| } |
| |
| static ssize_t in_read(struct audio_stream_in *stream, void *buffer, |
| size_t bytes) |
| { |
| struct stream_in *in = (struct stream_in *)stream; |
| struct audio_device *adev = in->dev; |
| int i, ret = -1; |
| |
| pthread_mutex_lock(&in->lock); |
| if (in->standby) { |
| pthread_mutex_lock(&adev->lock); |
| ret = start_input_stream(in); |
| pthread_mutex_unlock(&adev->lock); |
| if (ret != 0) { |
| goto exit; |
| } |
| in->standby = 0; |
| } |
| |
| if (in->pcm) { |
| ret = pcm_read(in->pcm, buffer, bytes); |
| } |
| |
| /* |
| * Instead of writing zeroes here, we could trust the hardware |
| * to always provide zeroes when muted. |
| */ |
| if (ret == 0 && adev->mic_mute) |
| memset(buffer, 0, bytes); |
| |
| exit: |
| pthread_mutex_unlock(&in->lock); |
| |
| if (ret != 0) { |
| in_standby(&in->stream.common); |
| ALOGV("%s: read failed - sleeping for buffer duration", __func__); |
| usleep(bytes * 1000000 / audio_stream_frame_size(&in->stream.common) / |
| in_get_sample_rate(&in->stream.common)); |
| } |
| return bytes; |
| } |
| |
| static uint32_t in_get_input_frames_lost(struct audio_stream_in *stream) |
| { |
| return 0; |
| } |
| |
| static int in_add_audio_effect(const struct audio_stream *stream, effect_handle_t effect) |
| { |
| return 0; |
| } |
| |
| static int in_remove_audio_effect(const struct audio_stream *stream, effect_handle_t effect) |
| { |
| return 0; |
| } |
| |
| static int adev_open_output_stream(struct audio_hw_device *dev, |
| audio_io_handle_t handle, |
| audio_devices_t devices, |
| audio_output_flags_t flags, |
| struct audio_config *config, |
| struct audio_stream_out **stream_out) |
| { |
| struct audio_device *adev = (struct audio_device *)dev; |
| struct stream_out *out; |
| int i, ret; |
| |
| ALOGD("%s: enter: sample_rate(%d) channel_mask(%#x) devices(%#x) flags(%#x)", |
| __func__, config->sample_rate, config->channel_mask, devices, flags); |
| *stream_out = NULL; |
| out = (struct stream_out *)calloc(1, sizeof(struct stream_out)); |
| |
| if (devices == AUDIO_DEVICE_NONE) |
| devices = AUDIO_DEVICE_OUT_SPEAKER; |
| |
| out->supported_channel_masks[0] = AUDIO_CHANNEL_OUT_STEREO; |
| out->channel_mask = AUDIO_CHANNEL_OUT_STEREO; |
| out->flags = flags; |
| out->devices = devices; |
| |
| /* Init use case and pcm_config */ |
| if (out->flags & AUDIO_OUTPUT_FLAG_DIRECT && |
| out->devices & AUDIO_DEVICE_OUT_AUX_DIGITAL) { |
| out->usecase = USECASE_AUDIO_PLAYBACK_MULTI_CH; |
| out->config = pcm_config_hdmi_multi; |
| |
| pthread_mutex_lock(&adev->lock); |
| read_hdmi_channel_masks(out); |
| pthread_mutex_unlock(&adev->lock); |
| |
| if (config->sample_rate == 0) config->sample_rate = DEFAULT_OUTPUT_SAMPLING_RATE; |
| if (config->channel_mask == 0) config->channel_mask = AUDIO_CHANNEL_OUT_5POINT1; |
| out->channel_mask = config->channel_mask; |
| out->config.rate = config->sample_rate; |
| out->config.channels = popcount(out->channel_mask); |
| out->config.period_size = HDMI_MULTI_PERIOD_BYTES / (out->config.channels * 2); |
| set_hdmi_channels(adev->mixer, out->config.channels); |
| } else if (out->flags & AUDIO_OUTPUT_FLAG_DEEP_BUFFER) { |
| out->usecase = USECASE_AUDIO_PLAYBACK_DEEP_BUFFER; |
| out->config = pcm_config_deep_buffer; |
| } else { |
| out->usecase = USECASE_AUDIO_PLAYBACK_LOW_LATENCY; |
| out->config = pcm_config_low_latency; |
| } |
| |
| if (flags & AUDIO_OUTPUT_FLAG_PRIMARY) { |
| if(adev->primary_output == NULL) |
| adev->primary_output = out; |
| else { |
| ALOGE("%s: Primary output is already opened", __func__); |
| return -EEXIST; |
| } |
| } |
| |
| /* Check if this usecase is already existing */ |
| pthread_mutex_lock(&adev->lock); |
| if (get_usecase_from_list(adev, out->usecase) != NULL) { |
| ALOGE("%s: Usecase (%d) is already present", __func__, out->usecase); |
| free(out); |
| *stream_out = NULL; |
| pthread_mutex_unlock(&adev->lock); |
| return -EEXIST; |
| } |
| pthread_mutex_unlock(&adev->lock); |
| |
| out->stream.common.get_sample_rate = out_get_sample_rate; |
| out->stream.common.set_sample_rate = out_set_sample_rate; |
| out->stream.common.get_buffer_size = out_get_buffer_size; |
| out->stream.common.get_channels = out_get_channels; |
| out->stream.common.get_format = out_get_format; |
| out->stream.common.set_format = out_set_format; |
| out->stream.common.standby = out_standby; |
| out->stream.common.dump = out_dump; |
| out->stream.common.set_parameters = out_set_parameters; |
| out->stream.common.get_parameters = out_get_parameters; |
| out->stream.common.add_audio_effect = out_add_audio_effect; |
| out->stream.common.remove_audio_effect = out_remove_audio_effect; |
| out->stream.get_latency = out_get_latency; |
| out->stream.set_volume = out_set_volume; |
| out->stream.write = out_write; |
| out->stream.get_render_position = out_get_render_position; |
| out->stream.get_next_write_timestamp = out_get_next_write_timestamp; |
| |
| out->dev = adev; |
| out->standby = 1; |
| |
| config->format = out->stream.common.get_format(&out->stream.common); |
| config->channel_mask = out->stream.common.get_channels(&out->stream.common); |
| config->sample_rate = out->stream.common.get_sample_rate(&out->stream.common); |
| |
| *stream_out = &out->stream; |
| ALOGD("%s: exit", __func__); |
| return 0; |
| } |
| |
| static void adev_close_output_stream(struct audio_hw_device *dev, |
| struct audio_stream_out *stream) |
| { |
| ALOGD("%s: enter", __func__); |
| out_standby(&stream->common); |
| free(stream); |
| ALOGD("%s: exit", __func__); |
| } |
| |
| static int adev_set_parameters(struct audio_hw_device *dev, const char *kvpairs) |
| { |
| struct audio_device *adev = (struct audio_device *)dev; |
| struct str_parms *parms; |
| char *str; |
| char value[32]; |
| int ret; |
| |
| ALOGD("%s: enter: %s", __func__, kvpairs); |
| |
| parms = str_parms_create_str(kvpairs); |
| ret = str_parms_get_str(parms, AUDIO_PARAMETER_KEY_TTY_MODE, value, sizeof(value)); |
| if (ret >= 0) { |
| int tty_mode; |
| |
| if (strcmp(value, AUDIO_PARAMETER_VALUE_TTY_OFF) == 0) |
| tty_mode = TTY_MODE_OFF; |
| else if (strcmp(value, AUDIO_PARAMETER_VALUE_TTY_VCO) == 0) |
| tty_mode = TTY_MODE_VCO; |
| else if (strcmp(value, AUDIO_PARAMETER_VALUE_TTY_HCO) == 0) |
| tty_mode = TTY_MODE_HCO; |
| else if (strcmp(value, AUDIO_PARAMETER_VALUE_TTY_FULL) == 0) |
| tty_mode = TTY_MODE_FULL; |
| else |
| return -EINVAL; |
| |
| pthread_mutex_lock(&adev->lock); |
| if (tty_mode != adev->tty_mode) { |
| adev->tty_mode = tty_mode; |
| adev->acdb_settings = (adev->acdb_settings & TTY_MODE_CLEAR) | tty_mode; |
| if (adev->in_call) |
| select_devices(adev, USECASE_VOICE_CALL); |
| } |
| pthread_mutex_unlock(&adev->lock); |
| } |
| |
| ret = str_parms_get_str(parms, AUDIO_PARAMETER_KEY_BT_NREC, value, sizeof(value)); |
| if (ret >= 0) { |
| /* When set to false, HAL should disable EC and NS |
| * But it is currently not supported. |
| */ |
| if (strcmp(value, AUDIO_PARAMETER_VALUE_ON) == 0) |
| adev->bluetooth_nrec = true; |
| else |
| adev->bluetooth_nrec = false; |
| } |
| |
| ret = str_parms_get_str(parms, "screen_state", value, sizeof(value)); |
| if (ret >= 0) { |
| if (strcmp(value, AUDIO_PARAMETER_VALUE_ON) == 0) |
| adev->screen_off = false; |
| else |
| adev->screen_off = true; |
| } |
| |
| str_parms_destroy(parms); |
| ALOGD("%s: exit with code(%d)", __func__, ret); |
| return ret; |
| } |
| |
| static char* adev_get_parameters(const struct audio_hw_device *dev, |
| const char *keys) |
| { |
| return strdup(""); |
| } |
| |
| static int adev_init_check(const struct audio_hw_device *dev) |
| { |
| return 0; |
| } |
| |
| static int adev_set_voice_volume(struct audio_hw_device *dev, float volume) |
| { |
| struct audio_device *adev = (struct audio_device *)dev; |
| int vol, err = 0; |
| |
| pthread_mutex_lock(&adev->lock); |
| adev->voice_volume = volume; |
| if (adev->mode == AUDIO_MODE_IN_CALL) { |
| if (volume < 0.0) { |
| volume = 0.0; |
| } else if (volume > 1.0) { |
| volume = 1.0; |
| } |
| |
| vol = lrint(volume * 100.0); |
| |
| // Voice volume levels from android are mapped to driver volume levels as follows. |
| // 0 -> 5, 20 -> 4, 40 ->3, 60 -> 2, 80 -> 1, 100 -> 0 |
| // So adjust the volume to get the correct volume index in driver |
| vol = 100 - vol; |
| |
| if (adev->csd_client) { |
| if (adev->csd_volume == NULL) { |
| ALOGE("%s: dlsym error for csd_client_volume", __func__); |
| } else { |
| err = adev->csd_volume(vol); |
| if (err < 0) { |
| ALOGE("%s: csd_client error %d", __func__, err); |
| } |
| } |
| } else { |
| ALOGE("%s: No CSD Client present", __func__); |
| } |
| } |
| pthread_mutex_unlock(&adev->lock); |
| return err; |
| } |
| |
| static int adev_set_master_volume(struct audio_hw_device *dev, float volume) |
| { |
| return -ENOSYS; |
| } |
| |
| static int adev_get_master_volume(struct audio_hw_device *dev, |
| float *volume) |
| { |
| return -ENOSYS; |
| } |
| |
| static int adev_set_master_mute(struct audio_hw_device *dev, bool muted) |
| { |
| return -ENOSYS; |
| } |
| |
| static int adev_get_master_mute(struct audio_hw_device *dev, bool *muted) |
| { |
| return -ENOSYS; |
| } |
| |
| static int adev_set_mode(struct audio_hw_device *dev, audio_mode_t mode) |
| { |
| struct audio_device *adev = (struct audio_device *)dev; |
| |
| pthread_mutex_lock(&adev->lock); |
| if (adev->mode != mode) { |
| adev->mode = mode; |
| } |
| pthread_mutex_unlock(&adev->lock); |
| return 0; |
| } |
| |
| static int adev_set_mic_mute(struct audio_hw_device *dev, bool state) |
| { |
| struct audio_device *adev = (struct audio_device *)dev; |
| int err = 0; |
| |
| pthread_mutex_lock(&adev->lock); |
| adev->mic_mute = state; |
| if (adev->mode == AUDIO_MODE_IN_CALL) { |
| if (adev->csd_client) { |
| if (adev->csd_mic_mute == NULL) { |
| ALOGE("%s: dlsym error for csd_mic_mute", __func__); |
| } else { |
| err = adev->csd_mic_mute(state); |
| if (err < 0) { |
| ALOGE("%s: csd_client error %d", __func__, err); |
| } |
| } |
| } else { |
| ALOGE("%s: No CSD Client present", __func__); |
| } |
| } |
| pthread_mutex_unlock(&adev->lock); |
| return err; |
| } |
| |
| static int adev_get_mic_mute(const struct audio_hw_device *dev, bool *state) |
| { |
| struct audio_device *adev = (struct audio_device *)dev; |
| |
| *state = adev->mic_mute; |
| |
| return 0; |
| } |
| |
| static size_t adev_get_input_buffer_size(const struct audio_hw_device *dev, |
| const struct audio_config *config) |
| { |
| int channel_count = popcount(config->channel_mask); |
| |
| return get_input_buffer_size(config->sample_rate, config->format, channel_count); |
| } |
| |
| static int adev_open_input_stream(struct audio_hw_device *dev, |
| audio_io_handle_t handle, |
| audio_devices_t devices, |
| struct audio_config *config, |
| struct audio_stream_in **stream_in) |
| { |
| struct audio_device *adev = (struct audio_device *)dev; |
| struct stream_in *in; |
| int ret, buffer_size, frame_size; |
| int channel_count = popcount(config->channel_mask); |
| |
| ALOGD("%s: enter", __func__); |
| *stream_in = NULL; |
| if (check_input_parameters(config->sample_rate, config->format, channel_count) != 0) |
| return -EINVAL; |
| |
| in = (struct stream_in *)calloc(1, sizeof(struct stream_in)); |
| |
| in->stream.common.get_sample_rate = in_get_sample_rate; |
| in->stream.common.set_sample_rate = in_set_sample_rate; |
| in->stream.common.get_buffer_size = in_get_buffer_size; |
| in->stream.common.get_channels = in_get_channels; |
| in->stream.common.get_format = in_get_format; |
| in->stream.common.set_format = in_set_format; |
| in->stream.common.standby = in_standby; |
| in->stream.common.dump = in_dump; |
| in->stream.common.set_parameters = in_set_parameters; |
| in->stream.common.get_parameters = in_get_parameters; |
| in->stream.common.add_audio_effect = in_add_audio_effect; |
| in->stream.common.remove_audio_effect = in_remove_audio_effect; |
| in->stream.set_gain = in_set_gain; |
| in->stream.read = in_read; |
| in->stream.get_input_frames_lost = in_get_input_frames_lost; |
| |
| in->device = devices; |
| in->source = AUDIO_SOURCE_DEFAULT; |
| in->dev = adev; |
| in->standby = 1; |
| in->channel_mask = config->channel_mask; |
| |
| /* Update config params with the requested sample rate and channels */ |
| in->usecase = USECASE_AUDIO_RECORD; |
| in->config = pcm_config_audio_capture; |
| in->config.channels = channel_count; |
| in->config.rate = config->sample_rate; |
| |
| frame_size = audio_stream_frame_size((struct audio_stream *)in); |
| buffer_size = get_input_buffer_size(config->sample_rate, |
| config->format, |
| channel_count); |
| in->config.period_size = buffer_size / frame_size; |
| |
| *stream_in = &in->stream; |
| ALOGD("%s: exit", __func__); |
| return 0; |
| |
| err_open: |
| free(in); |
| *stream_in = NULL; |
| return ret; |
| } |
| |
| static void adev_close_input_stream(struct audio_hw_device *dev, |
| struct audio_stream_in *stream) |
| { |
| ALOGD("%s", __func__); |
| |
| in_standby(&stream->common); |
| free(stream); |
| |
| return; |
| } |
| |
| static int adev_dump(const audio_hw_device_t *device, int fd) |
| { |
| return 0; |
| } |
| |
| static int adev_close(hw_device_t *device) |
| { |
| struct audio_device *adev = (struct audio_device *)device; |
| audio_route_free(adev->audio_route); |
| free(device); |
| return 0; |
| } |
| |
| static void init_platform_data(struct audio_device *adev) |
| { |
| char platform[PROPERTY_VALUE_MAX]; |
| char baseband[PROPERTY_VALUE_MAX]; |
| char value[PROPERTY_VALUE_MAX]; |
| |
| adev->dualmic_config = DUALMIC_CONFIG_NONE; |
| adev->fluence_in_spkr_mode = false; |
| adev->fluence_in_voice_call = false; |
| adev->fluence_in_voice_rec = false; |
| adev->mic_type_analog = false; |
| |
| property_get("persist.audio.handset.mic.type",value,""); |
| if (!strcmp("analog", value)) |
| adev->mic_type_analog = true; |
| |
| property_get("persist.audio.dualmic.config",value,""); |
| if (!strcmp("broadside", value)) { |
| adev->dualmic_config = DUALMIC_CONFIG_BROADSIDE; |
| adev->acdb_settings |= DMIC_FLAG; |
| } else if (!strcmp("endfire", value)) { |
| adev->dualmic_config = DUALMIC_CONFIG_ENDFIRE; |
| adev->acdb_settings |= DMIC_FLAG; |
| } |
| |
| if (adev->dualmic_config != DUALMIC_CONFIG_NONE) { |
| property_get("persist.audio.fluence.voicecall",value,""); |
| if (!strcmp("true", value)) { |
| adev->fluence_in_voice_call = true; |
| } |
| |
| property_get("persist.audio.fluence.voicerec",value,""); |
| if (!strcmp("true", value)) { |
| adev->fluence_in_voice_rec = true; |
| } |
| |
| property_get("persist.audio.fluence.speaker",value,""); |
| if (!strcmp("true", value)) { |
| adev->fluence_in_spkr_mode = true; |
| } |
| } |
| |
| adev->acdb_handle = dlopen(LIB_ACDB_LOADER, RTLD_NOW); |
| if (adev->acdb_handle == NULL) { |
| ALOGE("%s: DLOPEN failed for %s", __func__, LIB_ACDB_LOADER); |
| } else { |
| ALOGV("%s: DLOPEN successful for %s", __func__, LIB_ACDB_LOADER); |
| adev->acdb_deallocate = (acdb_deallocate_t)dlsym(adev->acdb_handle, |
| "acdb_loader_deallocate_ACDB"); |
| adev->acdb_send_audio_cal = (acdb_send_audio_cal_t)dlsym(adev->acdb_handle, |
| "acdb_loader_send_audio_cal"); |
| adev->acdb_send_voice_cal = (acdb_send_voice_cal_t)dlsym(adev->acdb_handle, |
| "acdb_loader_send_voice_cal"); |
| adev->acdb_init = (acdb_init_t)dlsym(adev->acdb_handle, |
| "acdb_loader_init_ACDB"); |
| if (adev->acdb_init == NULL) |
| ALOGE("%s: dlsym error %s for acdb_loader_init_ACDB", __func__, dlerror()); |
| else |
| adev->acdb_init(); |
| } |
| |
| /* If platform is Fusion3, load CSD Client specific symbols |
| * Voice call is handled by MDM and apps processor talks to |
| * MDM through CSD Client |
| */ |
| property_get("ro.board.platform", platform, ""); |
| property_get("ro.baseband", baseband, ""); |
| if (!strcmp("msm8960", platform) && !strcmp("mdm", baseband)) { |
| adev->csd_client = dlopen(LIB_CSD_CLIENT, RTLD_NOW); |
| if (adev->csd_client == NULL) |
| ALOGE("%s: DLOPEN failed for %s", __func__, LIB_CSD_CLIENT); |
| } |
| |
| if (adev->csd_client) { |
| ALOGV("%s: DLOPEN successful for %s", __func__, LIB_CSD_CLIENT); |
| adev->csd_client_deinit = (csd_client_deinit_t)dlsym(adev->csd_client, |
| "csd_client_deinit"); |
| adev->csd_disable_device = (csd_disable_device_t)dlsym(adev->csd_client, |
| "csd_client_disable_device"); |
| adev->csd_enable_device = (csd_enable_device_t)dlsym(adev->csd_client, |
| "csd_client_enable_device"); |
| adev->csd_start_voice = (csd_start_voice_t)dlsym(adev->csd_client, |
| "csd_client_start_voice"); |
| adev->csd_stop_voice = (csd_stop_voice_t)dlsym(adev->csd_client, |
| "csd_client_stop_voice"); |
| adev->csd_volume = (csd_volume_t)dlsym(adev->csd_client, |
| "csd_client_volume"); |
| adev->csd_mic_mute = (csd_mic_mute_t)dlsym(adev->csd_client, |
| "csd_client_mic_mute"); |
| adev->csd_client_init = (csd_client_init_t)dlsym(adev->csd_client, |
| "csd_client_init"); |
| |
| if (adev->csd_client_init == NULL) { |
| ALOGE("%s: dlsym error %s for csd_client_init", __func__, dlerror()); |
| } else { |
| adev->csd_client_init(); |
| } |
| } |
| } |
| |
| static int adev_open(const hw_module_t *module, const char *name, |
| hw_device_t **device) |
| { |
| struct audio_device *adev; |
| int i, ret; |
| |
| ALOGD("%s: enter", __func__); |
| if (strcmp(name, AUDIO_HARDWARE_INTERFACE) != 0) return -EINVAL; |
| |
| adev = calloc(1, sizeof(struct audio_device)); |
| |
| adev->mixer = mixer_open(MIXER_CARD); |
| if (!adev->mixer) { |
| ALOGE("Unable to open the mixer, aborting."); |
| return -ENOSYS; |
| } |
| |
| adev->audio_route = audio_route_init(MIXER_CARD, MIXER_XML_PATH); |
| if (!adev->audio_route) { |
| free(adev); |
| ALOGE("%s: Failed to init audio route controls, aborting.", __func__); |
| *device = NULL; |
| return -EINVAL; |
| } |
| |
| adev->device.common.tag = HARDWARE_DEVICE_TAG; |
| adev->device.common.version = AUDIO_DEVICE_API_VERSION_2_0; |
| adev->device.common.module = (struct hw_module_t *)module; |
| adev->device.common.close = adev_close; |
| |
| adev->device.init_check = adev_init_check; |
| adev->device.set_voice_volume = adev_set_voice_volume; |
| adev->device.set_master_volume = adev_set_master_volume; |
| adev->device.get_master_volume = adev_get_master_volume; |
| adev->device.set_master_mute = adev_set_master_mute; |
| adev->device.get_master_mute = adev_get_master_mute; |
| adev->device.set_mode = adev_set_mode; |
| adev->device.set_mic_mute = adev_set_mic_mute; |
| adev->device.get_mic_mute = adev_get_mic_mute; |
| adev->device.set_parameters = adev_set_parameters; |
| adev->device.get_parameters = adev_get_parameters; |
| adev->device.get_input_buffer_size = adev_get_input_buffer_size; |
| adev->device.open_output_stream = adev_open_output_stream; |
| adev->device.close_output_stream = adev_close_output_stream; |
| adev->device.open_input_stream = adev_open_input_stream; |
| adev->device.close_input_stream = adev_close_input_stream; |
| adev->device.dump = adev_dump; |
| |
| /* Set the default route before the PCM stream is opened */ |
| pthread_mutex_lock(&adev->lock); |
| adev->mode = AUDIO_MODE_NORMAL; |
| adev->active_input = NULL; |
| adev->primary_output = NULL; |
| adev->out_device = AUDIO_DEVICE_NONE; |
| adev->voice_call_rx = NULL; |
| adev->voice_call_tx = NULL; |
| adev->voice_volume = 1.0f; |
| adev->tty_mode = TTY_MODE_OFF; |
| adev->bluetooth_nrec = true; |
| adev->in_call = false; |
| adev->acdb_settings = TTY_MODE_OFF; |
| for (i = 0; i < SND_DEVICE_MAX; i++) { |
| adev->snd_dev_ref_cnt[i] = 0; |
| } |
| list_init(&adev->usecase_list); |
| pthread_mutex_unlock(&adev->lock); |
| |
| /* Loads platform specific libraries dynamically */ |
| init_platform_data(adev); |
| |
| *device = &adev->device.common; |
| |
| ALOGD("%s: exit", __func__); |
| return 0; |
| } |
| |
| static struct hw_module_methods_t hal_module_methods = { |
| .open = adev_open, |
| }; |
| |
| struct audio_module HAL_MODULE_INFO_SYM = { |
| .common = { |
| .tag = HARDWARE_MODULE_TAG, |
| .module_api_version = AUDIO_MODULE_API_VERSION_0_1, |
| .hal_api_version = HARDWARE_HAL_API_VERSION, |
| .id = AUDIO_HARDWARE_MODULE_ID, |
| .name = "QCOM Audio HAL", |
| .author = "Code Aurora Forum", |
| .methods = &hal_module_methods, |
| }, |
| }; |